Silver Series Installation and Operation Manual, Rev B ... - Watlow

More documents

Recommendations

Info

130 Silver Series Programming Manual3. As you can see, some of the parameters for a common window are disabled and cannot be changed.Window #4 is always reserved for the Common Window. Although the Background settings are active, noneof these settings affects the operation of the common window.4. Click OK. The Open Window dialog box reappears with the Common Window selected.5. If you wish to open the common window, click Open. Otherwise, click Close to return to the main screen ofEasyBuilder.Displaying the common window above/below the base windowThis setting resolves the conflict that can occur if a graphics object on the common window occupies the same spaceon the HMI display as a graphics object on a base window. Using the Above base window attribute forces thegraphics object on the common window to cover the base window graphics object. Using Below base window has theopposite effect.Base WindowCommon Window0600-0069-0000 Rev. B
Creating Windows 131When Above base window is set, the result is:When Below base window is set, the result is:To set the Above/Below base window option for a common window:1. From the Edit menu, select System Parameters. The Set System Parameters dialog box appears.2. Select the General tab. In the Options section next to Common window, select either Above base windowor Below base window.3. Click OK to return to the main screen of EasyBuilder. Active graphics objects (objects that display information or graphics according to a data value in a PLCregister or coil) take precedence over passive graphics objects (objects such as circles, lines, rectangles, etc.).Therefore, a Set Word Object on a base window will cover a Rectangle Object on a common window thatoccupies the same space even with the Above base screen attribute enabled.Changing the Active Common WindowAlthough only one common window can be on the HMI display at one time, you do have the ability to create multiplecommon windows by using base windows as common windows. Then, with the help of a Function Key object (usingthe Change common window checkbox), the HMI operator can change the active common window.The ability to change the common window adds more flexibility to your project should you need it. For example, youmay have a series of full screen windows which all need a keypad for entry. Another series of full screen windows mayrequire a common alarm message. By changing the common window with each series of windows, you can customizeeach common window to contain only the graphics objects that are needed.0600-0069-0000 Rev. B
Page 1 and 2:
Silver Series Operator Interface Te
Page 3 and 4:
iiiTable of ContentsCOPYRIGHT NOTIC
Page 5:
vChapter 11 - Capturing Alarms and
Page 8 and 9:
2 Silver Series Programming ManualC
Page 10 and 11:
4 Silver Series Programming ManualO
Page 13 and 14:
Introduction 7Video InInput and pla
Page 15 and 16:
HMI Local Setup 9The X-models (HMI5
Page 17 and 18:
HMI Local Setup 1110. Configure you
Page 19 and 20:
HMI Local Setup 1315. Click the VNC
Page 21 and 22:
HMI Local Setup 153. Click on the V
Page 23 and 24:
Connect the HMI to the PLC or Contr
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Creating a Sample Project 292. Clic
Page 37 and 38:
Creating a Sample Project 315. Sele
Page 39 and 40:
Creating a Sample Project 33Now let
Page 41 and 42:
Page 43 and 44:
Creating a Sample Project 373. In t
Page 45 and 46:
Creating a Sample Project 3916. Pas
Page 47 and 48:
Creating a Sample Project 413. In t
Page 49 and 50:
Creating a Sample Project 4311. Cli
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Creating a Sample Project 492. Conn
Page 57 and 58:
Simulator Mode 51Off-line simulatio
Page 59 and 60:
Using EZware-5000 53Chapter 6 - Usi
Page 61 and 62:
Using EZware-5000 55EasyBuilder-500
Page 63 and 64:
Using EZware-5000 57Numeric InputTh
Page 65 and 66:
Using EZware-5000 59Bar GraphThe Ba
Page 67 and 68:
Using EZware-5000 61XY PlotThe XY P
Page 69 and 70:
Using EZware-5000 63Alarm DisplayTh
Page 71 and 72:
Using EZware-5000 65Write data to P
Page 73 and 74:
Using EZware-5000 67When logging da
Page 75 and 76:
Using EZware-5000 69Managing Projec
Page 77 and 78:
Using EZware-5000 71Note: It is a g
Page 79 and 80:
Using EZware-5000 73Using the Windo
Page 81 and 82:
Using EZware-5000 75To zoom in on t
Page 83 and 84:
Using EZware-5000 774. Objects cut
Page 85 and 86: Using EZware-5000 79To delete a gra
Page 87 and 88: Using EZware-5000 81Bottom Layer:Pr
Page 89 and 90: Using EZware-5000 83To rotate objec
Page 91 and 92: Using EZware-5000 85To configure De
Page 93 and 94: Using EZware-5000 87To configure th
Page 95 and 96: Using EZware-5000 89To configure Ge
Page 97 and 98: Using EZware-5000 91To configure Sy
Page 99 and 100: Using EZware-5000 93To configure Se
Page 101 and 102: Using EZware-5000 95LW9500,LW9501LW
Page 103 and 104: Using EZware-5000 97To configure th
Page 105 and 106: Using EZware-5000 99Automatically R
Page 107 and 108: Using EZware-5000 1017. Click the E
Page 109 and 110: Using EZware-5000 1032. Display Mil
Page 111 and 112: Using EZware-5000 105Converting Mul
Page 113 and 114: Using EZware-5000 107Options Menu >
Page 115 and 116: Using EZware-5000 109integer format
Page 117 and 118: Using EZware-5000 111b. Save file a
Page 119 and 120: Using EZware-5000 113Off-line Simul
Page 121 and 122: Using EZware-5000 1155. Click Unins
Page 123 and 124: Creating Windows 1173. The Open Win
Page 125 and 126: Creating Windows 1194. Modify the w
Page 127 and 128: Creating Windows 121Assigning Under
Page 129 and 130: Creating Windows 1232. Highlight th
Page 131 and 132: Creating Windows 1252. Click New...
Page 133 and 134: Creating Windows 1274. Select the f
Page 135: Creating Windows 129 Placing a Clos
Page 139 and 140: Creating Windows 133When the HMI in
Page 141 and 142: Creating Windows 135Using the Fast
Page 143 and 144: Creating Windows 137The amount of a
Page 145 and 146: Creating and Using Databases and La
Page 153 and 154: Using and Creating Keypads 1472. Us
Page 155 and 156: Using and Creating Keypads 149Editi
Page 157 and 158: Bar Graphs, Meters, and Trends 151C
Page 159 and 160: Bar Graphs, Meters, and Trends 1536
Page 163 and 164: Bar Graphs, Meters, and Trends 157C
Page 169 and 170: Bar Graphs, Meters, and Trends 163T
Page 171 and 172: Bar Graphs, Meters, and Trends 165D
Page 173 and 174: Capturing Alarms and Events 167Chap
Page 175 and 176: Capturing Alarms and Events 1699. C
Page 177 and 178: Capturing Alarms and Events 1718. C
Page 179 and 180: Capturing Alarms and Events 173To c
Page 181 and 182: Security 175Chapter 12 - SecurityTh
Page 183 and 184: Security 177Object SecurityMany obj
Page 185 and 186: Security 179When Interlock is enabl
Page 187 and 188:
Security 181Additional Security Fea
Page 189 and 190:
Security 183XOB PasswordA project (
Page 191 and 192:
Security 185System PasswordsThe Sys
Page 193 and 194:
Security 187Upload Password: The pa
Page 195 and 196:
Security 189Upload (History) Passwo
show all

Silver Series Installation and Operation Manual, Rev B ... - Watlow

Create successful ePaper yourself

Delete template?

Save as template?