hager TX216 KNX/EIB DALI-Gateway - UTU

More documents

Recommendations

Info

hager"DALI Gateway C00Cx2" softwareParametersManual controlManual control in case ofbus voltage failureDisabledEnabledIn case of a bus voltage failure (bus voltageswitched off) you can determine whethermanual control is to be enabled ordisabled.Manual control duringbus modeDisabledEnabledFor the bus mode (bus voltage switchedon) you can determine whether manualcontrol is to be enabled or disabled.Disable function formanual control ?YesNoThe manual control can be disabled via thebus even with the manual control modeactivated. For this purpose the disableobject can be enabled at this point.Polarity of disable objectfor manual control0 = enabled / 1 = disabled1 = enabled / 0 = disabledThis parameter determines the polarity ofthe disable object.• Visible only in case of enabled disablefunction for manual control.• After a bus/ mains voltage return or afterprogramming with the ETS, the disablefunction will be immediately active(object value "0") in case of the setting:“1 = enabled / 0 = disabled”.Transmit manual controlstatus ?YesNoThe current status of the manual controlcan be transmitted to the bus via aseparate status object if bus voltage isactive (setting: “yes”).Seite 106 von 130
hager"DALI Gateway C00Cx2" softwareParametersFunction and polarity ofstatus objectThis parameter specifies the informationcontained in the status object. The objectwill always be "0" if the manual control hasbeen deactivated.0 = inactive; 1 = manualcontrol is active0 = inactive; 1 = permanentmanual control is activeThe object will be "1" if the manual controlhas been activated (temporarily orpermanently).The object will be “1” only if the permanentmanual control has been activated.• This parameter is visible only if thetransmission of the manual control statushas been enabled.• After bus voltage return, the status willbe actively transmitted to the bus ("0")only if a manual control that wasactivated during bus voltage failure hasbeen terminated by the return of the busvoltage. The status telegram will betransmitted without delay.Behaviour at the end ofpermanent manualcontrol during bus modeThe behaviour of the Gateway at the end ofthe permanent manual control depends onthis parameter.No changeTrack outputsAll telegrams received during an activepermanent manual control for direct control(switching, dimming, brightness value,scenes) will be discarded. After the end ofthe permanent manual control, the currentstatus of all groups remains unchanged. If,however, a forced-control position or adisable function has been activated beforeor during manual control, the Gateway willset the response parameterized for thisfunction for the relevant groups.During an active permanent manual controlall incoming telegrams are internallytracked. At the end of the manual controlthe groups will be set according to thecommand received last or to the status thatexisted prior to the manual control.Bus mode of individualgroups can be disabledYesNoIndividual groups can be locally disabledduring a permanent manual control so thatthe disabled groups can no longer beaddressed via the bus. A disable viamanual control will only be permitted if thisparameter has been set to “yes”.Seite 107 von 130
Page 3 and 4:
hagerProduct definition1 Product de
Page 5:
hagerFitting, electrical connection
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
hagerTechnical data3 Technical data
Page 20 and 21:
hagerSoftware specifications4 Softw
Page 22 and 23:
hager"DALI Gateway C00Cx2" software
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57: hager"DALI Gateway C00Cx2" software
Page 130: hager"DALI Gateway C00Cx2" software
show all

hager TX216 KNX/EIB DALI-Gateway - UTU

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?