hager TX216 KNX/EIB DALI-Gateway - UTU

More documents

Recommendations

Info

hager"DALI Gateway C00Cx2" softwareFunctional descriptionAutomatic shutoffThe shutoff function permits the automatic shutoff of a DALI group after the light intensity has beendimmed to a brightness value or jumped to and after this new brightness value falls below a shutoffbrightness adjusted in the ETS. There is the option available to configure a delay until the shutoff (cf.figure 19).The Shutoff function will be activated once a constant brightness value has been reached. Thus onlyafter a completed dimming operation. A new dimming operation that also ends below the shutoffbrightness will restart a configured delay, if applicable. The Shutoff function will be halted if the shutoffbrightness has been exceeded by a dimming operation.By applying the automatic shutoff function it is possible, for example, to not only set the lighting to aminimum brightness via relative dimming but also to shut it off. Another application, for example, is thetime controlled ‘Good night shutoff’ for the dimmed lighting of a children’s room.100 %Brightness value90 %Dimming operation50 %40 %30 %20 %Delay time(optional)Switchoff brightness10 %Switching statusfeedback0 %ONOFFtimetimeFigure 19: Dimming and switching response of the automatic shutoff function• Basically, the shutoff takes place without the Soft-OFF function - instantly.• The shutoff brightness can be adjusted within the dimmable brightness range between theparameterized maximum and minimum brightness. There will be no automatic shutoff if the shutoffbrightness = minimum brightness since the value may not remain under the shutoff brightness. Theshutoff function will be constantly active if the shutoff brightness has been configured to maximumbrightness and if the maximum brightness can be under-run at any time.• The feedback objects for the switching status and the brightness value will be updated via theautomatic shutoff function after the shutoff.Seite 66 von 130
hager"DALI Gateway C00Cx2" softwareFunctional descriptionThe shutoff function can also be combined with other functions of the DALI Gateway. In this case makesure that the disable function, the forced-control position function or the scene function will override theshutoff function (cf. figure 20). The shutoff automatic can only be activated via a dimming operation thatwas initiated via the 4-bit (“Dimming”) or 1-byte (“Brightness value”) communication objects. If theshutoff function is overridden, the DALI Gateway will terminate the processing of the delay time and theevaluation of the shutoff brightness.Switching-on (switch-on brightness) via the “Switching” communication object will not activate theshutoff function.Object"Disable" / "Forced-control"Object"staircase timerfunction start/stop"*Staircase timerfunction(timing)*Object"Central function"*Polarity ofcentral object*Object"Switching"*Time functionsSoft-ON / OFF **additional functionBehaviour- bus voltage failure- bus voltage return- ETS programmingBlinking*GroupObject"Dimming"lowerhigherScene priorityObject"Brightness value"Dimming speed /Dimming behaviourautomaticshutoff functionObject"Extension unit"*Scenecontrol*recallstoring **Object"Brightness valuefeedback"Object"Switchingfeedback"Verzögerung nachBusspannungswiederkehr*zyklisches Senden** = optional parameterization** = Basically, no new scene value willbe stored if a disable or forced-controlposition is active!Fig. 20: Functional diagram of the automatic shutoff functionEnabling the automatic shutoff functionThe automatic shutoff function can be set separately for each group in the plug-in of the DALI Gateway.• Set the “Automatic shutoff when falling below a specified brightness value ?” parameter in the"Groups - [x] group name - dimming" to “Yes“.The automatic shutoff function is now enabled. Other parameters will become visible.Seite 67 von 130
Page 3 and 4:
hagerProduct definition1 Product de
Page 5:
hagerFitting, electrical connection
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17: hagerFitting, electrical connection
Page 18 and 19: hagerTechnical data3 Technical data
Page 20 and 21: hagerSoftware specifications4 Softw
Page 22 and 23: hager"DALI Gateway C00Cx2" software
Page 116 and 117:
hager"DALI Gateway C00Cx2" software
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130:
show all

hager TX216 KNX/EIB DALI-Gateway - UTU

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?