hager TX216 KNX/EIB DALI-Gateway - UTU

More documents

Recommendations

Info

hager"DALI Gateway C00Cx2" softwareFunctional descriptionSetting the shutoff brightnessThe shutoff function requires the definition of the shutoff brightness. The shutoff brightness is setseparately for each DALI group.The shutoff function must be enabled.• Set the “Shutoff when brightness value is smaller” parameter in the "Groups - [x] group name -dimming" parameter node to the required brightness value.Once a dimming operation causes a value to fall below the parameterized shutoff brightness andonce the brightness has been set to constant, the DALI group will shut off or will start the delay untilthe shutoff. The selectable parameter must be within the limits of the maximum and minimumbrightness.Setting the delay of the shutoff functionA time delay can be activated before the shutoff function will automatically shut off when falling belowthe shutoff brightness at the end of a dimming operation. There is the option available to enable thetime delay separately for each DALI group.The shutoff function must be enabled.• Configure the “Delay until shutoff ?” parameter in the "Groups - [x] group name - dimming" to “Yes“.Once a dimming operation causes a value to fall below the parameterized shutoff brightness andonce the brightness has been set to constant, the DALI Gateway will trigger the delay time. The DALIgroup will completely shut off once the delay time has lapsed. The delay time can be retriggered byother dimming operations.Seite 68 von 130
hager"DALI Gateway C00Cx2" softwareFunctional descriptionTime delaysUp to two time functions can be independently set for each DALI group. The time functions act solelyon the "Switching" or "Switching central function" communication objects (if a central has beenactivated for the affected output) and will delay the received object value as a function of telegrampolarity (cf. fig. 21).Object"Disable" / "Forced-control"Object"staircase timerfunction start/stop"*Staircase timerfunction(timing)*Object"Central function"*Polarity ofcentral object*Object"Switching"Time functionsSoft-ON / OFF **additional functionBehaviour- bus voltage failure- bus voltage return- ETS programmingBlinking*GroupObject"Dimming"lowerhigherScene priorityObject"Brightness value"Dimming speed /Dimming behaviourautomaticshutoff function*Object"Extension unit"*Scenecontrol*recallstoring **Object"Brightness valuefeedback"Object"Switchingfeedback"Verzögerung nachBusspannungswiederkehr*zyklisches Senden** = optional parameterization** = Basically, no new scene value willbe stored if a disable or forced-controlposition is active!Fig.21: Functional diagram of the time delaysActivating an ON-delayThe On-delay can be parameterized separately for each group in the plug-in of the DALI Gateway.• Set the "Selection of time delay" parameter in the “Groups - [x] group name – Switch-on/switch-offbehaviour" parameter node to "ON-delay" or to "ON-delay and OFF-delay". Parameterize the desiredOn-delay time.The ON-delay is now enabled. The parameterized time will start after receiving an ON telegram viathe “Switching” object. A subsequent ON-telegram will retrigger the time only if the "ON-delayretriggerable ?" parameter has been set to "Yes". An OFF-telegram received during the ON-delay willterminate the delay and set the switching status to “OFF".Seite 69 von 130
Page 3 and 4:
hagerProduct definition1 Product de
Page 5:
hagerFitting, electrical connection
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19: hagerTechnical data3 Technical data
Page 20 and 21: hagerSoftware specifications4 Softw
Page 22 and 23: hager"DALI Gateway C00Cx2" software
Page 118 and 119:
hager"DALI Gateway C00Cx2" software
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130:
show all

hager TX216 KNX/EIB DALI-Gateway - UTU

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?