hager TX216 KNX/EIB DALI-Gateway - UTU

More documents

Recommendations

Info

hager"DALI Gateway C00Cx2" softwareSoftware information4.2.2 Software informationETS project design and commissioningFor creating a project and for the commissioning of this device it is recommended to use the ETS3.0dversion. Advantages with regards to downloading (significantly shorter loading times) can be expectedonly if this ETS patch version or later versions are used. The advantages result from the use of the newmask version 7.5 and the ETS3 support.The product database required for the ETS3.0d is offered in the *.VD4 format. The correspondingapplication program has the version number “1.1”. For older versions of the ETS3 a separate productdatabase is available in the *.VD2 format. The application program for these ETS versions is version"0.1".As far as the scope of functions described in this documentation is concerned, there is no differencebetween the two application programs.When older ETS versions are updated to the level of version ETS3.0d or to that of later versions, anadditional tool in the form of an ETS add-in is available. This tool is capable of converting older productdatabases of application version "0.1", for instance from existing ETS2 projects, into the newapplication format (version "1.1"). This feature permits making use of the advantages of the ETS3.0dapplication in an easy way and without creating any changes to the project design. The ETS3 add-incan be obtained separately from the manufacturer and is free of charge.Safe-state modeIf the device - for instance as a result of errors in the project design or during commissioning - does notwork properly, the execution of the loaded application program can be paused by activating the safestatemode. In the safe-state mode, the outputs cannot be controlled via the bus. A manual control forbroadcast is the only feature that can be activated. The Gateway remains passive in safe-state modesince the application program is not being executed (state-of-execution: terminated). Only the systemsoftware is still functional so that the ETS diagnosis functions and also the programming of the devicecontinue to be possible.Activating safe-state mode• Disconnect the mains voltage supply.• Press the programming key and keep it pressed.• Switch on the mains voltage supply. Release the programming key only after the programming LEDstarts blinking slowly.The safe-state mode is now activated. With another brief press on the programming key, theprogramming mode can be switched on and off as usual also in the safe-state mode. Theprogramming LED will nonetheless continue to blink independent of the programming mode as longas the safe-state mode remains active.• The safe-state mode can be terminated by switching off the mains voltage supply or by programmingwith the ETS.• For the activation of the safe-state mode, the bus voltage does not have to be switched on.Unloading the application programThe application program can be unloaded via the ETS. In this case, only manual control is possible forthe broadcast of connected DALI devices.Seite 22 von 130
hager"DALI Gateway C00Cx2" softwareObject table4.2.3 Object tableNumber of communication objects: 216Number of addresses (max): 254Number of assignments (max): 255Dynamic table management: noMaximum table length: 255Objects affecting several channels:Function: ScenesObject Function Name Type DP type Flag208 Extension unit Scenes 1- byte 18.001 C, W, -, (R) 1Description: 1-byte object for recalling scenes or for storing new scene values.Function:DALI fault and performance monitoringObject Function Name Type DP type Flag210 Feedback DALI error status 1-byte --- C, W, T, (R) 1 2Description:1-byte object for transmitting the error status of DALI devices that are connectedindividually to the system to the bus. The following bit assignment is used:Bit 0…5: number of the DALI device (0…63)Bit 6: lamp error (0 = no error, 1 = error)Bit 7: electronic ballast error (0 = no error, 1 = error)Independent of the feedback parameter setting, this object can always receivetelegrams (ValueWrite) as a transmission request. A received telegram will beimmediately answered via this object (ValueWrite) by transmitting the current internalobject status. Bits 0...5 in a request telegram must include the number of the DALIdevice. Bits 6 and 7 have to be set to “1”. Otherwise, the request telegram will beignored.1 Each communication object can be read-out. The readout requires the setting of the R flag.2 Depending on the parameterization the feedback objects are either actively transmitting (T flag) or can be passively read-out (R flag).Seite 23 von 130
Page 3 and 4: hagerProduct definition1 Product de
Page 5: hagerFitting, electrical connection
Page 8 and 9: hagerFitting, electrical connection
Page 18 and 19: hagerTechnical data3 Technical data
Page 20 and 21: hagerSoftware specifications4 Softw
Page 24 and 25: hager"DALI Gateway C00Cx2" software
Page 72 and 73:
hager"DALI Gateway C00Cx2" software
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130:
show all

hager TX216 KNX/EIB DALI-Gateway - UTU

Create successful ePaper yourself

Delete template?

Save as template?