Show HSE plan - Hitachi Power Europe GmbH

More documents

Recommendations

Info

Dok.-Nr. / Doc.-No.HPES-306-001-Standard HSE Plan englischThe scaffolding must be approved and labelled (Scafftag) by the subcontractor erecting the scaffolding.Unfinished areas must be cordoned off. Unlabelled scaffolding must not be used.3.4.18.2. Use of LaddersThe basic principle "steps before ladders" applies. Ladder use must be kept to a minimum. Laddersmay only be used for a short time to bridge the gap between small height differences.Ladders may not be used as a place of work. Before each use it must be checked whether a ladderis the best, safest way to access the relevant working area or temporary place of work. In somecases, for example, mobile scaffolding may be a better solution.All ladders must be kept in good condition. The rungs must be securely attached. Damaged laddersmust be removed immediately and repaired or replaced. All ladders must be inspected at regular intervals.Test logs must be kept in writing and be available on the construction site.Ladders must be positioned safely and secured so that they cannot slip. The correct pitch of theladder and the correct position of the worker must be checked regularly. The ladder must protrudeat least one metre above the point where the worker gets off.Metal ladders must not be used for electrical work.Ladders that are not being used must be removed.Ladders may be no more than seven metres high and only used with foot extenders. Pickling or hotliquids must not be used on ladders.3.4.18.3. Fall protection systemSide protection - barriersFall protection systems using side protection or barriers are required, for example, in: workplaces on or over water or other solid or liquid substances in which people could sink regardlessof the vertical drop. traffic routes on or over water or other solid or liquid substances in which people could sink regardlessof the vertical drop. exposed flights of stairs and landings, wall openings and on control platforms for machines andtheir access points with a vertical drop of more than 1.00m. Work places and traffic routes on roofs with a vertical drop of more than 3.00m. all other work places and traffic routes where there is a vertical drop of more than 2.00m. openings in floors, ceilings and roof surfaces of ≤ 9.00 m2 and edge lengths of ≤ 3.00 m and recesses.Fall guards● Side protection on the building edge can be dispensed with on work places and traffic routes onsurfaces with an incline of no more than 20 degrees if a fixed barrier is fitted at least 2.00 m fromthe edge, e.g. a handrail. chains, ropes but not fluttering cords.● Side protection or barriers can only be dispensed with if they are not possible for technical reasons,e.g. working on the building edge and instead catching devices (safety scaffold/ roof safetyscaffold/ catching nets/ protective walls) are available. Rope guards may only be used if catchingdevices are inappropriate.● The supervisor must specify the stop mechanisms and ensure that safety harnesses are used.VOR180_1 Seite / Page 42 ÷ 56HPES-306-001-e-Standard HSE Plan Ausg. / Issue 03.2011
Dok.-Nr. / Doc.-No.HPES-306-001-Standard HSE Plan englisch● For openings of ≤ 9.00 m 2 and edge lengths of ≤ 3,00 m and recesses, side protection on thebuilding edge may be dispensed with if they are fitted with attached immovable covers that can bewalked on.Side protection dimensions● Guard rails and middle rails must be secured so that they cannot be removed accidentally. Thetoe boards must not tip. Without static proof the following may be used as guard rails and middlerails:with a distance between the uprights of up to 2.00 m boards with a minimum cross section of 15 x 3cmwith a distance between the uprights of up to 3.00 m boards with a minimum cross section of 20 x 4cm or Ø 48.3 x 3.2 mm steel pipes or Ø 48.3 x 4 mm. aluminium pipes. Toe boards must projectbeyond the surface for at least 15 cm. Minimum thickness 3 cm.3.4.19. Radiography testsRadiography tests basically require a permit to work. The work is co-ordinated by the SiGeKo/Permit Manager.All official regulations that govern the use, storage and handling of a radiation source must be compliedwith.Dealing with radioactive materials is basically only permitted if corresponding handling permits areavailable in the subcontractor's name and a copy of the decision of the radiation protection officerhas been submitted to the site. Only officially recognised specialists are allowed to deal directly withradioactive materials.Contractors who work with radioactive materials must notify the client in writing of the time and theplace and the subcontractor's radiation protection officer at least one working day before workstarts. When carrying out radiography tests on welded seams in particular the responsible radiationprotection officer must check whether safety-related EMR measuring equipment in the vicinity ofthe test location can be affected.Places where a radioactive radiation source is used must be properly indicated and secured.The Radiation Protection Regulations (StrlSchV) and any riders and requirements of the handlingpermits in force must be strictly observed.In addition plant-specific regulations must be observed.Material tests with X-rays or gamma rays must be carried out either outside normal working hoursor, if possible, in special areas to which unauthorised people do not have access.A precise procedure description with a risk analysis must be compiled by the subcontractor carryingout the work which shows the work procedures, the equipment used and the safety zones and specialprotective measures in place. When the application is made this document must be submittedto the responsible authorities one week before the HPE work starts.Storage of radioactive materials on the site is forbidden.This permission to carry out the aforementioned work does not replace the pre-requisites that needlegal approval under the terms of the X-ray and radiation protection regulations.3.4.20. Fire and explosion preventionSubcontractors are responsible for checking whether sufficient precautionary measures have beentaken to prevent fire in their relevant work areas. The fire prevention topic is dealt with in detail inthe subcontractors' HSE plans.VOR180_1 Seite / Page 43 ÷ 56HPES-306-001-e-Standard HSE Plan Ausg. / Issue 03.2011
Page 1 and 2: akt. Ausgabe / current issue:01.03.
Page 3 and 4: Dok.-Nr. / Doc.-No.HPES-306-001-Sta
Page 41: Dok.-Nr. / Doc.-No.HPES-306-001-Sta

Show HSE plan - Hitachi Power Europe GmbH

Create successful ePaper yourself

Delete template?

Save as template?