JMA-5300MkIIsm

More documents

Recommendations

Info

INDEX > 4.Replacement Procedure > 4.6 Display Unit : Radar Process Unit NDC-1417 4) Remove the hexagonal support holding the coating clip in place, and lift the AIS process circuit out vertically and replace it. (Use the socket wrench for 5.5 mm bolts.) Remove 5) Reassemble the unit following the disassembly procedure in reverse. [Check points] 1) Check that the system starts up properly. 2) Check that no error message appears. 3) Check that the AIS button appears in the Target Information display area. AIS button 4-80
INDEX > 4.Replacement Procedure > 4.6 Display Unit : Radar Process Unit NDC-1417 4.6.7 GYRO Interface Unit replacement (NCT-59A) [Required tools] Phillips screwdriver for 3 mm screws [Replacement procedure] 1) Remove the four screws at the top of the process unit cover and the three screws on each side to remove the process unit cover. (Use the Phillips screwdriver for 3 mm screws.) 4 2) Remove the connected cable for the gyro log. Remove 3) Loosen the six screws holding the terminal board in place. (Use the Phillips screwdriver for 3 mm screws.) Loosen 4-81
Page 1:
JMA-5332-12 JMA-5322-7/9/6HS JMA-53
Page 4 and 5:
3.1.3 Circuit Block to be Repaired
Page 6 and 7:
6. Troubleshooting 6.1 Operation Te
Page 8 and 9:
7.3 Terminal Board Connection Diagr
Page 11 and 12:
INDEX > 1.System Overview > 1.1 Ove
Page 13 and 14:
INDEX > 1.System Overview > 1.3 Dis
Page 15 and 16:
Section 2 System Configulation 2.1
Page 17 and 18:
INDEX > 2.System Configulation > 2.
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43:
Section 3 Repair Parts 3.1 List of
Page 46 and 47:
INDEX > 3.Repair Parts > 3.1 List o
Page 48 and 49:
INDEX > 3.Repair Parts > 3.1 List o
Page 50 and 51:
INDEX > 3.Repair Parts > 3.2 Illust
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
4.2.17 Performance Monitor replacem
Page 74 and 75:
INDEX > 4.Replacement Procedure > 4
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103: INDEX > 4.Replacement Procedure > 4
Page 165 and 166: INDEX > 5.Updating Programs > 5.1 M
Page 167 and 168: INDEX > 5.Updating Programs > 5.3 V
Page 169 and 170: Section 6 Troubleshooting 6.1 Opera
Page 171: 6.6.3 Blurry image on the remote di
Page 174 and 175: INDEX > 6.Troubleshooting > 6.1 Ope
Page 180 and 181: INDEX > 6.Troubleshooting > 6.2 Sca
Page 192 and 193: INDEX > 6.Troubleshooting > 6.3 Dis
Page 202 and 203:
INDEX > 6.Troubleshooting > 6.4 Err
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
INDEX > 6.Troubleshooting > 6.5 Sam
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
INDEX > 6.Troubleshooting > 6.6 Ext
Page 222 and 223:
INDEX > 6.Troubleshooting > 6.6 Ext
Page 224 and 225:
7.3 Terminal Board Connection Diagr
Page 226 and 227:
INDEX > 7.Drawings > 7.1 Outline Dr
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
INDEX > 7.Drawings > 7.2 General Sy
Page 242 and 243:
INDEX > 7.Drawings > 7.3 Terminal B
Page 244 and 245:
INDEX > 7.Drawings > 7.3 Terminal B
Page 246 and 247:
6 4 2 1 INDEX > 7.Drawings > 7.4 In
Page 248 and 249:
5 2 4 1 INDEX > 7.Drawings > 7.4 In
Page 250 and 251:
INDEX > 7.Drawings > 7.4 Internal c
Page 252 and 253:
INDEX > 7.Drawings > 7.4 Internal c
Page 254 and 255:
INDEX > 7.Drawings > 7.5 Circuit Sc
Page 256 and 257:
Page 258:
show all

JMA-5300MkIIsm

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?