Soundtrack Pro 3 Effects Reference (en).pdf - Help Library - Apple

More documents

Recommendations

Info

78 Chapter 5 Filter Effects Getting to Know the AutoFilter Interface The main areas of the AutoFilter window are the Threshold, Envelope, LFO, Filter, Distortion, and Output parameter sections. Threshold parameter Envelope parameters LFO parameters Filter parameters Distortion parameters Output parameters • Threshold parameter: Sets an input level that—if exceeded—triggers the envelope or LFO, which are used to dynamically modulate the filter cutoff frequency. • Envelope parameters: Define how the filter cutoff frequency is modulated over time. • LFO parameters: Define how the filter cutoff frequency is modulated by the LFO. • Filter parameters: Control the tonal color of the filtered sound. • Distortion parameters: Distort the signal both before and after the filter. • Output parameters: Set the level of both the dry and effect signal. AutoFilter Threshold Parameter The Threshold parameter analyzes the level of the input signal. If the input signal level exceeds the set threshold level, the envelope and LFO are retriggered—this applies only if the Retrigger button is active.
The envelope and LFO can be used to modulate the filter cutoff frequency. AutoFilter Envelope Parameters The envelope is used to shape the filter cutoff over time. When the input signal exceeds the set threshold level, the envelope is triggered. • Attack knob and field: Sets the attack time for the envelope. • Decay knob and field: Sets the decay time for the envelope. • Sustain knob and field: Sets the sustain time for the envelope. If the input signal falls below the threshold level before the envelope sustain phase, the release phase is triggered. • Release knob and field: Sets the release time for the envelope (this is triggered as soon as the input signal falls below the threshold). • Dynamic knob and field: Determines the input signal modulation amount. You can modulate the peak value of the envelope section by varying this control. • Cutoff Mod. slider and field: Determines the impact of the envelope on the cutoff frequency. AutoFilter LFO Parameters The LFO is used as a modulation source for filter cutoff. • Coarse Rate knob, Fine Rate slider and field: Used to set the speed of LFO modulation. Drag the Coarse slider to set the LFO frequency in Hertz. Drag the Fine slider (the semicircular slider above the Rate knob) to fine-tune the frequency. Note: The labels shown for the Rate knob, slider, and field change when you activate Beat Sync. Chapter 5 Filter Effects 79
Page 1 and 2:
Soundtrack Pro 3 Effects Reference
Page 3 and 4:
Preface Chapter 1 Chapter 2 Chapter
Page 5:
Chapter 12 Chapter 13 153 153 155 1
Page 8 and 9:
Effect category Dynamics Processors
Page 11 and 12:
Delay Effects 1 Delay effects store
Page 13 and 14:
• Master section: This area conta
Page 15 and 16:
Tip: If the Overview display is hid
Page 17 and 18:
Delay Designer Tap Creation Suggest
Page 19 and 20:
Moving and Deleting Taps in Delay D
Page 21 and 22:
2 Vertically drag the bright line o
Page 23 and 24:
Editing Filter Cutoff in Delay Desi
Page 25 and 26:
Editing Taps in Delay Designer’s
Page 27 and 28: To reset the value of a tap Do one
Page 29 and 30: Use subtle variations of the grid p
Page 31 and 32: Stereo Delay The Stereo Delay works
Page 33: • Delay field: Sets the current d
Page 36 and 37: 36 Chapter 2 Distortion Effects Bit
Page 38 and 39: 38 Chapter 2 Distortion Effects •
Page 40 and 41: 40 Chapter 2 Distortion Effects •
Page 42 and 43: By reducing the highest parts of th
Page 44 and 45: • Out Ceiling knob and field: Set
Page 46 and 47: Setting Suitable Compressor Envelop
Page 48 and 49: Using the Enveloper The most import
Page 50 and 51: Limiter The Limiter works much like
Page 52 and 53: Multipressor Parameters The paramet
Page 54 and 55: Setting Multipressor Compression Pa
Page 56 and 57: Using the Noise Gate In most situat
Page 58 and 59: Surround Compressor Link Section Pa
Page 60 and 61: • Threshold knob and field: Sets
Page 62 and 63: 62 Chapter 4 Equalizers Channel EQ
Page 64 and 65: 64 Chapter 4 Equalizers You can red
Page 66 and 67: 66 Chapter 4 Equalizers Note: For b
Page 68 and 69: 68 Chapter 4 Equalizers • Analyze
Page 70 and 71: 70 Chapter 4 Equalizers Match EQ Pa
Page 72 and 73: Note: Smoothing has no effect on an
Page 74 and 75: The Q factor of the filter is deter
Page 76 and 77: 76 Chapter 4 Equalizers High Shelvi
Page 80 and 81: 80 Chapter 5 Filter Effects • Bea
Page 82 and 83: 82 Chapter 5 Filter Effects AutoFil
Page 84 and 85: • Sub Energy and field: Controls
Page 86 and 87: • Spread slider and field: Determ
Page 88 and 89: Understanding MS Miking To make a M
Page 91 and 92: Metering Tools 7 You can use the Me
Page 93 and 94: Using the MultiMeter Analyzer In An
Page 95 and 96: Using the MultiMeter’s Level Mete
Page 97 and 98: Although you can insert the Surroun
Page 99 and 100: Because the Surround MultiMeter Gon
Page 101 and 102: Depending on the chosen surround fo
Page 103: • Tuning Adjustment slider and fi
Page 106 and 107: Chorus Effect The Chorus effect del
Page 108 and 109: Flanger Effect The Flanger effect w
Page 110 and 111: • 180° or -180° is equal to the
Page 112 and 113: Ringshifter The Ringshifter effect
Page 114 and 115: • In the ring modulator OSC mode,
Page 116 and 117: Modulating the Ringshifter with the
Page 118 and 119: • Chorus Int knob: Sets the inten
Page 121 and 122: Pitch Effects 9 You can use the Pit
Page 123 and 124: Vocal Transformer Parameters The Vo
Page 125 and 126: Reverb Effects 10 You can use Rever
Page 127 and 128: PlatinumVerb The PlatinumVerb allow
Page 129 and 130:
PlatinumVerb Reverb Parameters The
Page 131 and 132:
Space Designer Convolution Reverb S
Page 133 and 134:
Working with Space Designer’s Imp
Page 135 and 136:
Any mono, stereo, AIFF, SDII, or WA
Page 137 and 138:
All envelopes are automatically cal
Page 139 and 140:
Whereas some parameters are envelop
Page 141 and 142:
Using Space Designer’s Density En
Page 143 and 144:
2 Drag the pointer horizontally ove
Page 145 and 146:
Note: Activation of the filter enve
Page 147 and 148:
• Spread and Xover knobs (synthes
Page 149 and 150:
Using Space Designer’s Rev Vol Co
Page 151 and 152:
This can be useful for eliminating
Page 153 and 154:
Specialized Effects and Utilities 1
Page 155 and 156:
Denoiser The Denoiser eliminates or
Page 157 and 158:
Using the Denoiser The following st
Page 159 and 160:
SubBass Parameters The SubBass offe
Page 161 and 162:
Utilities and Tools 13 The tools fo
Page 163:
Test Oscillator Test Oscillator gen
show all

Soundtrack Pro 3 Effects Reference (en).pdf - Help Library - Apple

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?