Distributed I/O System ET 200S

More documents

Recommendations

Info

Digital electronic modules 3.18 2DO 24 VAC to 230 VAC digital electronic module (6ES7132-4FB01-0AB0) Block diagram Figure 3-19 Block diagram of the 2DO 24-230 VAC 2DO 24 VAC to 230 VAC Technical Specifications (6ES7132-4FB01-0AB0) Dimensions W × H × D (mm) Dimensions and Weight 15 × 81 × 52 (the total dimensions depend on the selected terminal module) Weight Approx. 37 g Supports isochronous operation Data for specific modules no Number of outputs Cable length 2 • Unshielded max. 600 m • Shielded max. 1000 m Parameter length 3 bytes Voltages, currents, potentials Rated load voltage L1 (from the power module) 24 to 230 VAC • Frequency 47 to 63 Hz Total current of the outputs (per module) • Up to 40° C max. 2 A1 • Up to 60° C max. 1 A1 Galvanic isolation • Between the channels no • Between the channels and backplane bus Yes Insulation tested 2500 VDC ET 200S 3-74 Manual, 12/2005, A5E00514527-03
Digital electronic modules 3.18 2DO 24 VAC to 230 VAC digital electronic module (6ES7132-4FB01-0AB0) Current consumption • From the backplane bus max. 18 mA • From rated load voltage L1 (no load) max. 15 mA per channel Power dissipation of the module max. 4 W Status, interrupts, diagnostics Status display Green LED per channel Diagnostics function Output voltage no Data for selecting an actuator • At signal "1" min. L (-1.5 V) Output current (per channel) • At signal "1" – Rated value 2 A – Permitted range 0.1 mA to 2.2 A • With signal "0" (leakage current) max. 3 mA Output delay (for resistive load) • at "0" to "1" max. 15 ms • At "1" to "0" max. 15 ms Zero cross inhibit voltage Motor starter size max. 25 V • Up to 40° C Max. size in accordance with NEMA: 5 • Up to 60° C Max. size in accordance with NEMA: 4 Lamp load Connecting two outputs in parallel max. 100 W • For redundant triggering of a load Yes (per module) • To increase performance no Control of a digital input Switch rate supported • For resistive load max. 10 Hz • On inductive load max. 0.5 Hz • For lamp load max. 1 Hz Short-circuit protection of the output Yes, by means of fuse in the power module 1 Total current of the outputs (per module): see the diagram below ET 200S Manual, 12/2005, A5E00514527-03 3-75
Page 1 and 2:
SIMATIC Distributed I/O System ET 2
Page 3 and 4:
Table of contents 1 Terminal module
Page 5 and 6:
Table of contents 4.3 Basics of ana
Page 7:
Table of contents Table 4-10 SIMATI
Page 10 and 11:
Terminal modules 1.1 Terminal modul
Page 12 and 13:
Terminal modules 1.3 TM-P15S22-01,
Page 14 and 15:
Terminal modules 1.4 TM-P30S44-A0 a
Page 16 and 17:
Terminal modules 1.5 TM-PF30S47-F1
Page 18 and 19:
Terminal modules 1.6 TM-E15S26-A1,
Page 20 and 21:
Terminal modules 1.8 TM-E15S24-01,
Page 22 and 23:
Terminal modules 1.9 TM-E15S23-01,
Page 24 and 25:
Terminal modules 1.10 Terminal modu
Page 26 and 27:
Terminal modules 1.12 TM-E30S44-01
Page 28 and 29:
Terminal modules 1.13 TM-C120S and
Page 30 and 31:
Terminal modules 1.14 TE-U120S4x10
Page 32 and 33:
Power modules 2.2 Parameters for po
Page 34 and 35:
Power modules 2.3 PM-E 24 VDC power
Page 36 and 37:
Power modules 2.4 PM-E 24-48 VDC po
Page 38 and 39:
Power modules 2.4 PM-E 24-48 VDC po
Page 40 and 41:
Power modules 2.5 PM-E 24-48 VDC/24
Page 42 and 43:
Power modules 2.5 PM-E 24-48 VDC/24
Page 44 and 45:
Power modules 2.6 Placing power mod
Page 46 and 47:
Power modules 2.7 Example of a conf
Page 48 and 49:
Power modules 2.8 Finding the corre
Page 50 and 51:
Digital electronic modules 3.1 Para
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Digital electronic modules 3.3 2DI
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73: Digital electronic modules 3.7 4DI
Page 96 and 97: Digital electronic modules 3.12 2DO
Page 100 and 101: Digital electronic modules 3.13 Sta
Page 102 and 103: Digital electronic modules 3.13 Sta
Page 124 and 125: Digital electronic modules 3.19 2RO
Page 136 and 137: Analog electronics modules 4.2 Anal
Page 150 and 151: Analog electronics modules 4.3 Basi
Page 160 and 161: Analog electronics modules 4.4 Resp
Page 162 and 163: Analog electronics modules 4.5 Para
Page 172 and 173:
Analog electronics modules 4.6 2AI
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Analog electronics modules 4.19 2AO
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 252 and 253:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 254 and 255:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 256 and 257:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.3
Page 258 and 259:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.3
Page 260 and 261:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.3
Page 262 and 263:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.4
Page 264 and 265:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.4
Page 266 and 267:
Potential distributor module 6.1 Po
Page 268 and 269:
Potential distributor module 6.1 Po
Page 270 and 271:
RESERVE modules Pin assignment Note
Page 272 and 273:
Glossary Configuration Connecting t
Page 274 and 275:
Glossary Frequency converter Ground
Page 276 and 277:
Glossary Power modules Prewiring Pr
Page 278 and 279:
Glossary Real time Reference potent
Page 280 and 281:
Glossary Terminal modules Terminati
Page 282 and 283:
Index Analog electronic module 2AI
Page 284 and 285:
Index T Terminal module TM-E15S24-0
Page 286 and 287:
Safety Guidelines This manual conta
Page 288 and 289:
Table of contents ET 200S iv Produc
Page 290 and 291:
Introduction ET 200S 1-2 Product In
Page 292 and 293:
New Information About the "ET 200S
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Index ET 200S Index-2 Product Infor
Page 320 and 321:
Safety Guidelines This manual conta
Page 322 and 323:
Table of contents Distributed I/O S
Page 324 and 325:
Introduction 1.1 Introduction Distr
Page 326 and 327:
Product Information 2.2 Digital Ele
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Index Distributed I/O System ET 200
Page 340 and 341:
Product Information on Manual Distr
show all

Distributed I/O System ET 200S

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?