Distributed I/O System ET 200S

More documents

Recommendations

Info

RESERVE modules Pin assignment Note If you use RESERVE modules: • The SF LED lights up on the interface module • A channel-specific diagnostic and module status "10B: Wrong module" are reported for the RESERVE module slot. The RESERVE module has no connection to the terminals of the TM-E terminal module. This enables you to fully wire the TM-E terminal module and prepare it for the subsequent application. RESERVE Module Technical Specifications (6ES7138-4AAx1-0AA0) Reference Dimensions and Weight Dimension W x H x D (mm) 15 x 81 x 52 30 x 81 x 52 Weight Approx. 33 g (installation width 15 mm) Approx. 55 g (installation width 30 mm) Voltages, currents, potentials Power dissipation of the module Typically 0.025 W Status, interrupts, diagnostics Status display no Diagnostics function no Note The address space must correspond with the address space of the planned electronic module. For information on the option handling and implementation of RESERVE modules can be found in the ET 200S Operating Instructions in Functions > Option Handling on the PROFIBUS DP. ET 200S 7-2 Manual, 12/2005, A5E00514527-03
Glossary Aggregate current Total of all currents of all output channels of a digital output module. Automation system An automation system is a programmable control system, consisting of at least one CPU, various input and output modules as well as operating and monitoring devices. AUX1 bus Backplane bus Baud rate Bus Bus connector Power modules permit you to connect any additional potential (up to 230 VAC), which you can apply by means of the AUX(iliary) bus. You can use the AUX(iliary) bus as required: • As a protective conductor bar • For additional voltage when required The backplane bus is a serial data bus via which the interface module IM 151-1 communicates with the electronic modules/motor starters and supplies them with the necessary voltage. The connection between the individual modules is established by means of the terminal modules. The Baud rate is the speed at which data is transmitted and specifies the number of bits transmitted per second (Baud rate = bit rate). In the case of the ET 200S, baud rates of 9.6 kBaud to 12 MBaud are possible. A common transfer route connecting all nodes and having two defined ends. In the case of the ET 200, the bus is a two-wire or fiber-optic cable. A physical connection between the bus node and the bus line. ET 200S Manual, 12/2005, A5E00514527-03 Glossary-1
Page 1 and 2:
SIMATIC Distributed I/O System ET 2
Page 3 and 4:
Table of contents 1 Terminal module
Page 5 and 6:
Table of contents 4.3 Basics of ana
Page 7:
Table of contents Table 4-10 SIMATI
Page 10 and 11:
Terminal modules 1.1 Terminal modul
Page 12 and 13:
Terminal modules 1.3 TM-P15S22-01,
Page 14 and 15:
Terminal modules 1.4 TM-P30S44-A0 a
Page 16 and 17:
Terminal modules 1.5 TM-PF30S47-F1
Page 18 and 19:
Terminal modules 1.6 TM-E15S26-A1,
Page 20 and 21:
Terminal modules 1.8 TM-E15S24-01,
Page 22 and 23:
Terminal modules 1.9 TM-E15S23-01,
Page 24 and 25:
Terminal modules 1.10 Terminal modu
Page 26 and 27:
Terminal modules 1.12 TM-E30S44-01
Page 28 and 29:
Terminal modules 1.13 TM-C120S and
Page 30 and 31:
Terminal modules 1.14 TE-U120S4x10
Page 32 and 33:
Power modules 2.2 Parameters for po
Page 34 and 35:
Power modules 2.3 PM-E 24 VDC power
Page 36 and 37:
Power modules 2.4 PM-E 24-48 VDC po
Page 38 and 39:
Power modules 2.4 PM-E 24-48 VDC po
Page 40 and 41:
Power modules 2.5 PM-E 24-48 VDC/24
Page 42 and 43:
Power modules 2.5 PM-E 24-48 VDC/24
Page 44 and 45:
Power modules 2.6 Placing power mod
Page 46 and 47:
Power modules 2.7 Example of a conf
Page 48 and 49:
Power modules 2.8 Finding the corre
Page 50 and 51:
Digital electronic modules 3.1 Para
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Digital electronic modules 3.3 2DI
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Digital electronic modules 3.12 2DO
Page 98 and 99:
Page 100 and 101:
Digital electronic modules 3.13 Sta
Page 102 and 103:
Digital electronic modules 3.13 Sta
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Digital electronic modules 3.19 2RO
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Analog electronics modules 4.2 Anal
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Analog electronics modules 4.3 Basi
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Analog electronics modules 4.4 Resp
Page 162 and 163:
Analog electronics modules 4.5 Para
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Analog electronics modules 4.6 2AI
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221: Analog electronics modules 4.16 2AI
Page 232 and 233: Analog electronics modules 4.19 2AO
Page 250 and 251: 4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 266 and 267: Potential distributor module 6.1 Po
Page 268 and 269: Potential distributor module 6.1 Po
Page 272 and 273: Glossary Configuration Connecting t
Page 274 and 275: Glossary Frequency converter Ground
Page 276 and 277: Glossary Power modules Prewiring Pr
Page 278 and 279: Glossary Real time Reference potent
Page 280 and 281: Glossary Terminal modules Terminati
Page 282 and 283: Index Analog electronic module 2AI
Page 284 and 285: Index T Terminal module TM-E15S24-0
Page 286 and 287: Safety Guidelines This manual conta
Page 288 and 289: Table of contents ET 200S iv Produc
Page 290 and 291: Introduction ET 200S 1-2 Product In
Page 292 and 293: New Information About the "ET 200S
Page 318 and 319: Index ET 200S Index-2 Product Infor
Page 320 and 321:
Safety Guidelines This manual conta
Page 322 and 323:
Table of contents Distributed I/O S
Page 324 and 325:
Introduction 1.1 Introduction Distr
Page 326 and 327:
Product Information 2.2 Digital Ele
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Index Distributed I/O System ET 200
Page 340 and 341:
Product Information on Manual Distr
show all

Distributed I/O System ET 200S

Create successful ePaper yourself

Delete template?

Save as template?