Distributed I/O System ET 200S

More documents

Recommendations

Info

Power modules 2.4 PM-E 24-48 VDC power module (6ES7138-4CA50-0AA0) PM-E 24 VDC to 48 VDC technical specifications (6ES7138-4CA50-0AA0) Reference Dimensions W × H × D (mm) Dimensions and Weight 15 × 81 × 52 (the total dimensions depend on the selected terminal module) Weight Approx. 35 g Rated load voltage Voltages, currents, potentials 24 VDC to 48 VDC • Reverse polarity protection Yes • Overvoltage protection no Protection with automatic circuit breakers yes, tripping characteristic B, C Max. current-carrying capacity (up to 60° C) 10 A • Short-circuit protection no Galvanic isolation • Between rated load voltage and backplane bus Yes • Between the power modules Yes Insulation test voltage Current consumption 500 VDC • From the load voltage L+ (no load) max. 12 mA Power dissipation of the module typ. 500 mW Parameter length 3 bytes Status, interrupts, diagnostics Diagnostic function Yes • Group error Red "SF" LED • Load voltage monitoring Green "PWR" LED • Diagnostic information readable Yes Information on the address space of the inputs and outputs can be found in the ET 200S Operating Instructions. ET 200S 2-8 Manual, 12/2005, A5E00514527-03
2.5 2.5 Characteristics Replacing the fuse: Power modules 2.5 PM-E 24-48 VDC/24-230 VAC power module (6ES7138-4CB11-0AB0) PM-E 24-48 VDC/24-230 VAC power module (6ES7138-4CB11-0AB0) General terminal assignment The PM-E 24 VDC to 48 VDC/24 VAC to 230 VAC power module • Monitors the supply voltage for all the electronic modules in the voltage group. The supply voltage is fed in by means of the TM-P terminal module. • Can be used universally and can be assigned parameters for DC and AC load voltage for use with any electronic module. • Is required at least once for the ET 200S (to the right of the interface module). Exception: Design of the ET 200S with an IM151-1 COMPACT • Control interface (PIQ) and feedback interface (PII) in the process image for option handling. • The current status of the power module is stored in the status byte in the process input image (PII). This is updated irrespective of whether the "No Load Voltage" diagnosis has been enabled. • Is additionally equipped with a replaceable fuse (5 mm x 20 mm). 1 (1) Screwdriver with 3 mm blade (2) Fuse Note Terminals A4 and A8 are only available at specified terminal modules. ET 200S Manual, 12/2005, A5E00514527-03 2-9 2
Page 1 and 2: SIMATIC Distributed I/O System ET 2
Page 3 and 4: Table of contents 1 Terminal module
Page 5 and 6: Table of contents 4.3 Basics of ana
Page 7: Table of contents Table 4-10 SIMATI
Page 10 and 11: Terminal modules 1.1 Terminal modul
Page 12 and 13: Terminal modules 1.3 TM-P15S22-01,
Page 14 and 15: Terminal modules 1.4 TM-P30S44-A0 a
Page 16 and 17: Terminal modules 1.5 TM-PF30S47-F1
Page 18 and 19: Terminal modules 1.6 TM-E15S26-A1,
Page 20 and 21: Terminal modules 1.8 TM-E15S24-01,
Page 22 and 23: Terminal modules 1.9 TM-E15S23-01,
Page 24 and 25: Terminal modules 1.10 Terminal modu
Page 26 and 27: Terminal modules 1.12 TM-E30S44-01
Page 28 and 29: Terminal modules 1.13 TM-C120S and
Page 30 and 31: Terminal modules 1.14 TE-U120S4x10
Page 32 and 33: Power modules 2.2 Parameters for po
Page 34 and 35: Power modules 2.3 PM-E 24 VDC power
Page 36 and 37: Power modules 2.4 PM-E 24-48 VDC po
Page 40 and 41: Power modules 2.5 PM-E 24-48 VDC/24
Page 42 and 43: Power modules 2.5 PM-E 24-48 VDC/24
Page 44 and 45: Power modules 2.6 Placing power mod
Page 46 and 47: Power modules 2.7 Example of a conf
Page 48 and 49: Power modules 2.8 Finding the corre
Page 50 and 51: Digital electronic modules 3.1 Para
Page 56 and 57: Digital electronic modules 3.3 2DI
Page 88 and 89:
Digital electronic modules 3.9 4DI
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Digital electronic modules 3.12 2DO
Page 98 and 99:
Page 100 and 101:
Digital electronic modules 3.13 Sta
Page 102 and 103:
Digital electronic modules 3.13 Sta
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Digital electronic modules 3.19 2RO
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Analog electronics modules 4.2 Anal
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Analog electronics modules 4.3 Basi
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Analog electronics modules 4.4 Resp
Page 162 and 163:
Analog electronics modules 4.5 Para
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Analog electronics modules 4.6 2AI
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Analog electronics modules 4.19 2AO
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 252 and 253:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 254 and 255:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.2
Page 256 and 257:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.3
Page 258 and 259:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.3
Page 260 and 261:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.3
Page 262 and 263:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.4
Page 264 and 265:
4 IQ-SENSE (6ES7138-4GA00-0AB0) 5.4
Page 266 and 267:
Potential distributor module 6.1 Po
Page 268 and 269:
Potential distributor module 6.1 Po
Page 270 and 271:
RESERVE modules Pin assignment Note
Page 272 and 273:
Glossary Configuration Connecting t
Page 274 and 275:
Glossary Frequency converter Ground
Page 276 and 277:
Glossary Power modules Prewiring Pr
Page 278 and 279:
Glossary Real time Reference potent
Page 280 and 281:
Glossary Terminal modules Terminati
Page 282 and 283:
Index Analog electronic module 2AI
Page 284 and 285:
Index T Terminal module TM-E15S24-0
Page 286 and 287:
Safety Guidelines This manual conta
Page 288 and 289:
Table of contents ET 200S iv Produc
Page 290 and 291:
Introduction ET 200S 1-2 Product In
Page 292 and 293:
New Information About the "ET 200S
Page 294 and 295:
Page 296 and 297:
Page 298 and 299:
Page 300 and 301:
Page 302 and 303:
Page 304 and 305:
Page 306 and 307:
Page 308 and 309:
Page 310 and 311:
Page 312 and 313:
Page 314 and 315:
Page 316 and 317:
Page 318 and 319:
Index ET 200S Index-2 Product Infor
Page 320 and 321:
Safety Guidelines This manual conta
Page 322 and 323:
Table of contents Distributed I/O S
Page 324 and 325:
Introduction 1.1 Introduction Distr
Page 326 and 327:
Product Information 2.2 Digital Ele
Page 328 and 329:
Page 330 and 331:
Page 332 and 333:
Page 334 and 335:
Page 336 and 337:
Page 338 and 339:
Index Distributed I/O System ET 200
Page 340 and 341:
Product Information on Manual Distr
show all

Distributed I/O System ET 200S

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?