SwitchBlade x3112 Installation Guide - Allied Telesis

More documents

Recommendations

Info

Chapter 3: Troubleshooting AT-SBx31XZ4 XFP Line Card Port LED is Off For fiber optic uplink ports that have an XFP transceiver installed, verify that the 1000 LINK LED is ON. If a 1000 LINK LED is off but the transceiver is present, do the following: Verify that the end node connected to the port is powered ON and is operating properly. Check that the fiber optic cable is securely connected to the XFP transceiver in the AT-SBx31XZ4 XFP Line Card and to the port on the remote end node. The dual ports in an XFP transceiver consist of two separate connectors, where each connector connects to a separate fiber strand. 1858 Figure 70. Dual Ports of XFP Transceiver When you connect a fiber optic cable, be sure that the receive fiber connector of the XFP transceiver is connected to the transmit connector on the remote end node, and that the transmit fiber connector is connected to the receive connector on the remote node. Verify that the XFP transceiver is IEEE 802.3ae (10G Ethernet) and XFP MSA compliant. If an XFP transceiver meets a “Fiber Channel” standard, it may not link up. Verify that the XFP transceiver is completely inserted into the XFP slot. Make sure that you are using the appropriate type of fiber optic cable and that the cable length does not exceed the allowed maximum distance. For cable specifications, refer to the data sheet for your XFP transceiver. Use a fiber optic tester to test the attenuation on the cable to determine if the strength of the fiber optic signal falls below acceptable limits. For fiber optic port specifications, refer to the data sheet for your XFP transceiver. Check that the operating specifications (for instance, wavelength and maximum operating distance) of the fiber optic port on the remote end node are compatible with the fiber optic port on the AT-SBx31XZ4 XFP Line Card. 102
SwitchBlade x3112 Installation Guide Check to be sure that the fiber optic ports on theAT-SBx31XZ4 XFP Line Card and on the remote end node are operating at the same speed and duplex mode. Verify that any optional XFP transceivers are completely inserted into the SP slot on the front of the switch. 103
Page 1 and 2:
M/S PSU FAN MASTER SLAVE NORMAL FAU
Page 3 and 4:
Electrical Safety and Emissions Sta
Page 5 and 6:
Contents Preface ..................
Page 7 and 8:
List of Figures Figure 1: Front Vie
Page 9 and 10:
List of Tables Table 1. Safety Symb
Page 11 and 12:
Preface This guide provides the har
Page 13 and 14:
SwitchBlade x3112 Installation Guid
Page 15 and 16:
Chapter 1 Overview This chapter pro
Page 17 and 18:
POWER SwitchBlade x3112 Installatio
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
1808 SwitchBlade x3112 Installation
Page 47 and 48:
Page 49 and 50:
Chapter 2 Installation This chapter
Page 51 and 52: SwitchBlade x3112 Installation Guid
Page 61 and 62: P O E 0 2 4 6 8 P O E S Y S T E M 1
Page 67 and 68: POWER SwitchBlade x3112 Installatio
Page 73 and 74: SBx31CFC SYS STATUS M/S PSU FAN M/S
Page 75 and 76: SYS STATUS M/S PSU FAN 10/100/1000B
Page 77 and 78: 0 1 22 23 SwitchBlade x3112 Install
Page 85 and 86: P O E 0 2 4 6 8 10 P O E SBx31FAN P
Page 91 and 92: POE PSU A and C PSU B and D PSU POW
Page 93 and 94: SYS STATUS 10/100/1000Base-T Switch
Page 95 and 96: Chapter 3 Troubleshooting This chap
Page 101: SwitchBlade x3112 Installation Guid
Page 105 and 106: Appendix A Technical Specifications
show all

SwitchBlade x3112 Installation Guide - Allied Telesis

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?