SwitchBlade x3112 Installation Guide - Allied Telesis

More documents

Recommendations

Info

Chapter 1: Overview The NET MGMT port is a standard RJ-45 8-pin connector and can operate at 10, 100, or 1000 Mbps in either half- or full-duplex mode. The cable requirements for this port can be found in the table “Cable Requirements for the 10/100/1000Base-T Management Port” on page 112. For the port pinouts, refer to “Connectors and Port Pinouts” on page 110. The default setting for the Management port is Auto-Negotiation with Auto MDI/MDI-X. At the default setting, the port, which is IEEE 802.3u compliant, sets its speed and duplex mode automatically with Auto-Negotiation. You can disable Auto-Negotiation and set the speed and duplex mode manually. The wiring configuration of the port is set automatically with Auto MDI/MDI-X to MDI or MDI-X, depending on the wiring configuration of the end node. This allows you to use a straight-through twisted-pair cable regardless of the wiring configuration of the port on the network device. The Auto MDI/MDI-X feature is only available when the port is using Auto-Negotiation. If the Auto-Negotiation feature is disabled with the Switchblade x3112 Management Software, the port defaults to the MDI-X setting. NET MGMT LED The Network Management (NET MGMT) port on the AT-SBx31CFC Fabric Control Card has one Status LED as displayed in Figure 8 and described in Table 6. Table 6. NET MGMT port LED Description LED State Description L/A Solid Green Flashing Green Solid Amber Flashing Amber The port has a valid 1000 Mbps link. The port is transmitting or receiving data at 1000 Mbps. The port has a valid 100 or 10 Mbps link. The port is transmitting or receiving data at 100 or 10 Mbps. Console (RS-232) Port You use this port for local management with a console or a PC with a terminal emulation program. See Figure 8. This port does not require the AT-SBx31CFC Fabric Control Card to have an Internet Protocol (IP) address and is referred to as local or out-of-band management because it is not conducted over a network. When initially configuring your SwitchBlade x3112 Switch, you first connect to this port with an RS-232 Serial Management cable. The cable is provided with the AT-SBx31CFC Fabric Control Card. 26
SwitchBlade x3112 Installation Guide For instructions on how to start a local management session, refer to Chapter 2, “Starting a Local Management Session” on page 93 or refer to the Software Reference for SwitchBlade x3100 Series Switches on the ATI web site. Go to “Where to Find Web-based Guides” on page 13 for information about how to navigate to this document. USB Port The USB slot is an interface designed for temporary storage of configuration files on a memory stick. This interface is presently unsupported by the Switchblade x3112 Management Software and will be available in future software releases. SD Card Slot The SD slot for a secure digital memory (SD) card is displayed in Figure 9 and is used in the following situations: Storing backup copies of the master configuration file on the AT-SBx31CFC Fabric Control Card. You can maintain a library of past configuration files of a chassis so that you can return a unit to a previous configuration. Transferring master configuration files between chassis - You can configure units that are to have similar configurations by transferring the master configuration file with a secure digital memory card. SD READY BUSY FAULT 1818 Figure 9 SD Card Slot and LED An SD card is optional. The AT-SBx31CFC Fabric Control Card can operate without a memory card. The following SD flash memory cards are officially supported in the first release. SanDisk 2GB Flash card SanDisk 4GB SDHC Flash card Note Other brands can be used but are not guaranteed to work. For ordering information, contact your Allied Telesis sales representative or visit our web site. 27
Page 1 and 2: M/S PSU FAN MASTER SLAVE NORMAL FAU
Page 3 and 4: Electrical Safety and Emissions Sta
Page 5 and 6: Contents Preface ..................
Page 7 and 8: List of Figures Figure 1: Front Vie
Page 9 and 10: List of Tables Table 1. Safety Symb
Page 11 and 12: Preface This guide provides the har
Page 13 and 14: SwitchBlade x3112 Installation Guid
Page 15 and 16: Chapter 1 Overview This chapter pro
Page 17 and 18: POWER SwitchBlade x3112 Installatio
Page 25: SwitchBlade x3112 Installation Guid
Page 45 and 46: 1808 SwitchBlade x3112 Installation
Page 49 and 50: Chapter 2 Installation This chapter
Page 61 and 62: P O E 0 2 4 6 8 P O E S Y S T E M 1
Page 67 and 68: POWER SwitchBlade x3112 Installatio
Page 73 and 74: SBx31CFC SYS STATUS M/S PSU FAN M/S
Page 75 and 76: SYS STATUS M/S PSU FAN 10/100/1000B
Page 77 and 78:
0 1 22 23 SwitchBlade x3112 Install
Page 79 and 80:
SwitchBlade x3112 Installation Guid
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
P O E 0 2 4 6 8 10 P O E SBx31FAN P
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
POE PSU A and C PSU B and D PSU POW
Page 93 and 94:
SYS STATUS 10/100/1000Base-T Switch
Page 95 and 96:
Chapter 3 Troubleshooting This chap
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Appendix A Technical Specifications
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
show all

SwitchBlade x3112 Installation Guide - Allied Telesis

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?