SwitchBlade x3112 Installation Guide - Allied Telesis

More documents

Recommendations

Info

Chapter 2: Installation Warning: Reliable earthing of rack-mounted equipment should be maintained. Particular attention should be given to supply connections other than direct connections to the branch circuits (e.g., use of power strips). E37 Warning: To reduce the risk of electric shock, the PoE ports on this product must not connect to cabling that is routed outside the building where this device is located. E40 Warning: This product may have multiple AC power cords installed. To de-energize this equipment, disconnect all power cords from the device. E43 Caution: An Energy Hazard exists inside this equipment. Do not insert hands or tools into open chassis slots or sockets. E44 Warning: This equipment shall be installed in a Restricted Access location. E45 Warning: High Leakage Current exists in this chassis. Connect external ground wire before connecting AC power supply(s). E46 52
SwitchBlade x3112 Installation Guide Selecting a Site for the SwitchBlade x3112 Observe the following requirements before installing your switch in an equipment rack: For countries that require 100-125 VAC installations, the power cord plug provided with the AT-SBx3161 System Power Supply and the AT- SBx3165 PoE Power Supply assemblies has a 20 Amp, 125 V NEMA 5-20P plug. This plug is only compatible with a NEMA 5-20R receptacle. See Figure 26, “100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle”. G W 1965 Figure 26. 100 - 125 VAC 125 V NEMA 5-20 Plug and Receptacle Ensure that the rack is safely secured and that it will not tip over. Devices in a rack should be installed starting at the bottom, with the heavier devices near the bottom of the rack. The power outlet for the switch should be located near the unit and should be easily accessible. If the chassis has a system and PoE power supplies installed, the power sources for multiple supplies of the same type should be on different A/C circuits to protect the unit from a power circuit failure. Use dedicated power circuits or power conditioners to supply reliable electrical power to the network devices. The site should provide easy access to the ports on the front of the chassis so that you can easily connect and disconnect the network cables, as well as view the unit’s LEDs. Air flow around the unit and through the side and rear vents should be unrestricted. Do not place objects on top of the switch. Do not expose the switch to moisture or water. Ensure that the site is a dust-free environment. 53
Page 1 and 2: M/S PSU FAN MASTER SLAVE NORMAL FAU
Page 3 and 4: Electrical Safety and Emissions Sta
Page 5 and 6: Contents Preface ..................
Page 7 and 8: List of Figures Figure 1: Front Vie
Page 9 and 10: List of Tables Table 1. Safety Symb
Page 11 and 12: Preface This guide provides the har
Page 13 and 14: SwitchBlade x3112 Installation Guid
Page 15 and 16: Chapter 1 Overview This chapter pro
Page 17 and 18: POWER SwitchBlade x3112 Installatio
Page 45 and 46: 1808 SwitchBlade x3112 Installation
Page 49 and 50: Chapter 2 Installation This chapter
Page 51: SwitchBlade x3112 Installation Guid
Page 61 and 62: P O E 0 2 4 6 8 P O E S Y S T E M 1
Page 67 and 68: POWER SwitchBlade x3112 Installatio
Page 73 and 74: SBx31CFC SYS STATUS M/S PSU FAN M/S
Page 75 and 76: SYS STATUS M/S PSU FAN 10/100/1000B
Page 77 and 78: 0 1 22 23 SwitchBlade x3112 Install
Page 85 and 86: P O E 0 2 4 6 8 10 P O E SBx31FAN P
Page 91 and 92: POE PSU A and C PSU B and D PSU POW
Page 93 and 94: SYS STATUS 10/100/1000Base-T Switch
Page 95 and 96: Chapter 3 Troubleshooting This chap
Page 103 and 104:
SwitchBlade x3112 Installation Guid
Page 105 and 106:
Appendix A Technical Specifications
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
show all

SwitchBlade x3112 Installation Guide - Allied Telesis

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?