Accusetter Manual - BC MacDonald & Co.

More documents

Recommendations

Info

Typical IO <strong>Co</strong>nnections - I/O Board #5911013 OUTPUT "SINKING" IO A/B IO A/B P13 LOAD +24 VDC (+) LOAD P13 CURRENT FLOW GOOD RELAY P19 0 VDC (-) P19 - 24VDC Power Supply + OUTPUT "SOURCING" IO A/B IO A/B P13 LOAD +24 VDC (+) P19 CURRENT FLOW GOOD RELAY P19 0 VDC (-) LOAD P13 + 24VDC Power Supply - Figure 2.5 2-9
RS232C (9 Pin Female DSUB) Figure 2.6 - RS-232C Pins <strong>Accusetter</strong> II Cable External Device Pin 1 = Chassis Ground. ß----------------------------à Chassis Ground. Pin 2 = Receive (RXD) ß----------------------------à (TXD) Transmit. Pin 3 = Transmit (TXD) ß----------------------------à (RXD) Receive. Pin 5 = Signal Ground ß----------------------------à Signal Ground. Note: Pin2 and 3 are jumper selectable based upon the application. 2-10
Page 1 and 2: Support: 800-875-7243 How to Use Th
Page 3 and 4: Table of Contents Preface Manual Re
Page 5 and 6: Table of Figures Figure 1.1 - Progr
Page 7 and 8: Introduction 1.0 Summary and Featur
Page 9 and 10: 1.3 Glossary of Terms Absolute disp
Page 11 and 12: A Signal Conditioner is a circuit b
Page 13 and 14: Programming Reference Guide The fol
Page 15 and 16: 2.1 Specifications Overall Dimensio
Page 17 and 18: 2.4 Front Panel The Accusetter II f
Page 19 and 20: 2.5 Rear Panel The Accusetter II re
Page 21: 2.6 Pin Assignments for Rear Panel
Page 25 and 26: 2.8 E9320 (4) Channel LVDT Signal C
Page 27 and 28: 2.10 E9340 (2) Channel A/E Signal C
Page 29 and 30: Basic Operation 3.0 Set up and Oper
Page 31 and 32: Rear Mounting Bracket Front Mountin
Page 33 and 34: Multiple Accusetter II Setup 1) Tur
Page 35 and 36: 3.3 Programming Choose The Proper P
Page 37 and 38: Accusetter II Programming Guide The
Page 39 and 40: An example of various multipliers a
Page 41 and 42: Multiple Check Formulas If the Accu
Page 43 and 44: PROGRAMMING - SINGLE CHECK MEASUREM
Page 51 and 52: PROGRAMMING - MULTIPLE CHECK MEASUR
Page 59 and 60: PROGRAMMING - MULTIPLE FIXTURE MEAS
Page 67 and 68: PROGRAMMING - SYSTEM OPTIONS Progra
Page 69 and 70: PROGRAMMING - SYSTEM OPTIONS Buss I
Page 71 and 72: PROGRAMMING - SYSTEM OPTIONS AUTO A
Page 73 and 74:
For example, for the above example
Page 75 and 76:
3.5 Calibration NOTE: Prior to perf
Page 77 and 78:
Multiple Check Applications In a mu
Page 79 and 80:
Multiple Fixture Application In a m
Page 81 and 82:
3.6 Operation Single Check Operatio
Page 83 and 84:
Multiple Check or Multiple Fixture
Page 85 and 86:
Offloading Gage Results You may opt
Page 87 and 88:
Output Pin Selection Jumper The ele
Page 89 and 90:
4.1 Air/Electronic Maintenance Main
Page 91 and 92:
4.2 LVDT Signal Conditioning Module
Page 93 and 94:
Figure 4.5 - Input/Output Jumpers 4
Page 95 and 96:
LVDT Module Installation 1) Turn of
Page 97 and 98:
4.4 Communications RS232 Communicat
Page 99 and 100:
RS-232 Data Collector Offloading Th
Page 101 and 102:
(RS-232 Personal Computer, continue
Page 103 and 104:
(RS-232 Personal Computer, continue
Page 105 and 106:
The format for a parameter download
Page 107 and 108:
4.5 Input/Output Board Accusetter I
Page 109 and 110:
Figure 4.8 E8204 Connections The Ac
Page 111 and 112:
Auto Air Setup NOTE: The air check(
Page 113 and 114:
4.7 Troubleshooting Error Unit will
Page 115 and 116:
Input/Output signal not reading pro
Page 117 and 118:
Index Anti-Static Precautions 1-2 A
Page 119:
Warranty Information A one year war
show all

Accusetter Manual - BC MacDonald & Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?