Accusetter Manual - BC MacDonald & Co.

More documents

Recommendations

Info

2.11 Supply Air Filter/Regulator Assembly Any unit supplied with an A/E signal conditioning module will also be supplied with a filter/regulator assembly. The assembly is mounted to the rear foot of the Accusetter II. The regulator is factory preset to 44psi and requires a clean, dry air supply at 60psi min. The regulator output is connected to a fitting on the A/E module that extends out of the 44psi inlet port on the rear panel of the Accusetter II. Figure 2.11 - Supply Air Filter/Regulator 2-15
Basic Operation 3.0 Set up and Operation Summary The following steps must be taken to prepare the Accusetter II for operation. 1) Unpack and setup the unit. See "Unpacking & Setup" below. 2) Setup signal conditioning module jumpers and install module. See the "Advanced Operation" section. Power to the column must be turned off prior to installing or removing a signal conditioning module. 3) Program Accusetter II for the application. See the "Programming" section below. 4) Set up magnification and zero for the air gage input or inputs. See "Input Setup" below or set up the LVDT probes. See "Input Setup" below. 5) Calibrate the gage(s). See "Calibration". 6) Select Run mode and unit is ready for gaging. See "Operation". 3-1
Page 1 and 2: Support: 800-875-7243 How to Use Th
Page 3 and 4: Table of Contents Preface Manual Re
Page 5 and 6: Table of Figures Figure 1.1 - Progr
Page 7 and 8: Introduction 1.0 Summary and Featur
Page 9 and 10: 1.3 Glossary of Terms Absolute disp
Page 11 and 12: A Signal Conditioner is a circuit b
Page 13 and 14: Programming Reference Guide The fol
Page 15 and 16: 2.1 Specifications Overall Dimensio
Page 17 and 18: 2.4 Front Panel The Accusetter II f
Page 19 and 20: 2.5 Rear Panel The Accusetter II re
Page 21 and 22: 2.6 Pin Assignments for Rear Panel
Page 23 and 24: RS232C (9 Pin Female DSUB) Figure 2
Page 25 and 26: 2.8 E9320 (4) Channel LVDT Signal C
Page 27: 2.10 E9340 (2) Channel A/E Signal C
Page 31 and 32: Rear Mounting Bracket Front Mountin
Page 33 and 34: Multiple Accusetter II Setup 1) Tur
Page 35 and 36: 3.3 Programming Choose The Proper P
Page 37 and 38: Accusetter II Programming Guide The
Page 39 and 40: An example of various multipliers a
Page 41 and 42: Multiple Check Formulas If the Accu
Page 43 and 44: PROGRAMMING - SINGLE CHECK MEASUREM
Page 51 and 52: PROGRAMMING - MULTIPLE CHECK MEASUR
Page 59 and 60: PROGRAMMING - MULTIPLE FIXTURE MEAS
Page 67 and 68: PROGRAMMING - SYSTEM OPTIONS Progra
Page 69 and 70: PROGRAMMING - SYSTEM OPTIONS Buss I
Page 71 and 72: PROGRAMMING - SYSTEM OPTIONS AUTO A
Page 73 and 74: For example, for the above example
Page 75 and 76: 3.5 Calibration NOTE: Prior to perf
Page 77 and 78: Multiple Check Applications In a mu
Page 79 and 80:
Multiple Fixture Application In a m
Page 81 and 82:
3.6 Operation Single Check Operatio
Page 83 and 84:
Multiple Check or Multiple Fixture
Page 85 and 86:
Offloading Gage Results You may opt
Page 87 and 88:
Output Pin Selection Jumper The ele
Page 89 and 90:
4.1 Air/Electronic Maintenance Main
Page 91 and 92:
4.2 LVDT Signal Conditioning Module
Page 93 and 94:
Figure 4.5 - Input/Output Jumpers 4
Page 95 and 96:
LVDT Module Installation 1) Turn of
Page 97 and 98:
4.4 Communications RS232 Communicat
Page 99 and 100:
RS-232 Data Collector Offloading Th
Page 101 and 102:
(RS-232 Personal Computer, continue
Page 103 and 104:
(RS-232 Personal Computer, continue
Page 105 and 106:
The format for a parameter download
Page 107 and 108:
4.5 Input/Output Board Accusetter I
Page 109 and 110:
Figure 4.8 E8204 Connections The Ac
Page 111 and 112:
Auto Air Setup NOTE: The air check(
Page 113 and 114:
4.7 Troubleshooting Error Unit will
Page 115 and 116:
Input/Output signal not reading pro
Page 117 and 118:
Index Anti-Static Precautions 1-2 A
Page 119:
Warranty Information A one year war
show all

Accusetter Manual - BC MacDonald & Co.

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?