Accusetter Manual - BC MacDonald & Co.

More documents

Recommendations

Info

The last consideration to complete the formula is the gaging function. See examples below: 3-12
Multiple Check Formulas If the <strong>Accusetter</strong> is programmed for multiple check operation then the results of checks 1, 2, and/or 3 can be combine algebraically. For an example of a multiple check application consider and air plug that measures a part ID at two elevations. The large diameter is measured with input A and displays the large diameter size as check #1. The small diameter is measured with input B and displays the small diameter size as check #2. To display the part taper check #3 can be defined as a multiple check to display the results of check #1 minus check #2. Check #1, Large Diameter Function = AVG Formula = A x (+)1.000 Check #2, Small Diameter Function = AVG Formula = B x (+)1.000 Check #3, Multiple Check, Taper Function = AVG Formula = CHK1 x (+)1.000 + CHK2 x (-)1.000 3-13
Page 1 and 2: Support: 800-875-7243 How to Use Th
Page 3 and 4: Table of Contents Preface Manual Re
Page 5 and 6: Table of Figures Figure 1.1 - Progr
Page 7 and 8: Introduction 1.0 Summary and Featur
Page 9 and 10: 1.3 Glossary of Terms Absolute disp
Page 11 and 12: A Signal Conditioner is a circuit b
Page 13 and 14: Programming Reference Guide The fol
Page 15 and 16: 2.1 Specifications Overall Dimensio
Page 17 and 18: 2.4 Front Panel The Accusetter II f
Page 19 and 20: 2.5 Rear Panel The Accusetter II re
Page 21 and 22: 2.6 Pin Assignments for Rear Panel
Page 23 and 24: RS232C (9 Pin Female DSUB) Figure 2
Page 25 and 26: 2.8 E9320 (4) Channel LVDT Signal C
Page 27 and 28: 2.10 E9340 (2) Channel A/E Signal C
Page 29 and 30: Basic Operation 3.0 Set up and Oper
Page 31 and 32: Rear Mounting Bracket Front Mountin
Page 33 and 34: Multiple Accusetter II Setup 1) Tur
Page 35 and 36: 3.3 Programming Choose The Proper P
Page 37 and 38: Accusetter II Programming Guide The
Page 39: An example of various multipliers a
Page 43 and 44: PROGRAMMING - SINGLE CHECK MEASUREM
Page 51 and 52: PROGRAMMING - MULTIPLE CHECK MEASUR
Page 59 and 60: PROGRAMMING - MULTIPLE FIXTURE MEAS
Page 67 and 68: PROGRAMMING - SYSTEM OPTIONS Progra
Page 69 and 70: PROGRAMMING - SYSTEM OPTIONS Buss I
Page 71 and 72: PROGRAMMING - SYSTEM OPTIONS AUTO A
Page 73 and 74: For example, for the above example
Page 75 and 76: 3.5 Calibration NOTE: Prior to perf
Page 77 and 78: Multiple Check Applications In a mu
Page 79 and 80: Multiple Fixture Application In a m
Page 81 and 82: 3.6 Operation Single Check Operatio
Page 83 and 84: Multiple Check or Multiple Fixture
Page 85 and 86: Offloading Gage Results You may opt
Page 87 and 88: Output Pin Selection Jumper The ele
Page 89 and 90: 4.1 Air/Electronic Maintenance Main
Page 91 and 92:
4.2 LVDT Signal Conditioning Module
Page 93 and 94:
Figure 4.5 - Input/Output Jumpers 4
Page 95 and 96:
LVDT Module Installation 1) Turn of
Page 97 and 98:
4.4 Communications RS232 Communicat
Page 99 and 100:
RS-232 Data Collector Offloading Th
Page 101 and 102:
(RS-232 Personal Computer, continue
Page 103 and 104:
(RS-232 Personal Computer, continue
Page 105 and 106:
The format for a parameter download
Page 107 and 108:
4.5 Input/Output Board Accusetter I
Page 109 and 110:
Figure 4.8 E8204 Connections The Ac
Page 111 and 112:
Auto Air Setup NOTE: The air check(
Page 113 and 114:
4.7 Troubleshooting Error Unit will
Page 115 and 116:
Input/Output signal not reading pro
Page 117 and 118:
Index Anti-Static Precautions 1-2 A
Page 119:
Warranty Information A one year war
show all

Accusetter Manual - BC MacDonald & Co.

Create successful ePaper yourself

Delete template?

Save as template?