R308 AT Command Manual - wless.ru

More documents

Recommendations

Info

R308 AT Commands REMS – Remote S-Register Access Read Command ATREMS:,XX[X[x]] Examples ATREMS:000D6F00000AAC93,00 ATREMS:000D6F00000AAC93,0AE ATREMS:000D6F00000AAC93,1812 Where can be the remote node‟s EUI64, NodeID or address table index and XX is the S-Register which is to be read. As an option for all 16 bit registers it is also possible to address an individual bit only by specifying the bit number [X]. For all 32 bit registers it is possible to address an individual bit by specifying the bit number in hexadecimal [xx] The result when reading a single bit will always be 0 or 1. Note: Also the local node can be the target of this command (e.g. use address table entry FF as the address) Response SEQ:XX OK or ERROR: The module asks for the contents of the remote S- register using a unicast. The sequence number of the unicast is displayed (an ACK or NACK prompt will follow). represents the error code explained in section 3. Prompt SREAD:,,, [=] Where NodeID is the remote NodeID, EUI64 is the remote EUI64, Register is the S-Register which was read and is indicating the success (00) or failure of the read operation. The contents of the remote S-Register are following in case of a successful read only. Write Command ATREMS:,XX[x[x]]= [,] Examples ATREMS:000D6F0000012345,00=3FFC ATREMS:000D6F0000012345,0AE=1:pass word Where can be the remote node‟s EUI64, NodeID or address table index and XX is the S-Register which is to be written. As an option for all 16- and 32-bit registers it is also possible to address an individual bit only by specifying the bit number [x[x]]. Response SEQ:XX OK or ERROR: The data is written to the remote S-register number XX and if applicable stored in non-volatile memory. The data format for each individual S Register is given in the S-Register description. The sequence number of the unicast is displayed (an ACK or NACK prompt will follow). represents the error code explained in section 3. Prompt SWRITE:,, Notes Some S-Registers require a password for write access. See S-Register description for details. The default password for R3xx is “password”. Some S-Registers are read-only and will return an error if you are trying to write to them. When writing an individual bit by specifying [x[x]], can only be either 0 or 1. Where is the remote NodeID, is the remote EUI64. Only in case the errorcode is 00 the write operation has been completed successfully. SW release R302 ● ©2012 Telegesis (UK) Ltd - 16 - AT Command Manual (Rev 3.08)
R308 AT Commands SALL – Remote S-Register Access Write Command ATSALL:,XX[x[x]]= [,] Examples ATSALL:FFFF,00=3FFC ATSALL:FFFC,0AE=1:password Where group IDs are remote node‟s multicast IDs or FFFF - Broadcast to all devices FFFD - Broadcast to all non-sleepy devices FFFC – Broadcast to all Routers Response OK or ERROR: The data is written to the remote S-register number XX on all nodes addressed by the multicast group ID. The data format for each individual S Register is given in the S-Register description. represents the error code explained in section 3. For all 16- and 32-bit registers individual bits can also be set or cleared by specifying the bit using hexadecimal [x[x]] and setting it to either 0 or 1. Notes Some S-Registers require a password for write access. See S-Register description for details. The default password for R3xx is “password”. Some S-Registers are read-only and cannot be written to. SW release R300 ● +TOKDUMP – Display All S-Registers Execute Command AT+TOKDUMP Notes Only used on the local node. You cannot display all the registers of a remote device. Response OK The module displays the contents of all local S- Registers. The data format for each individual S Register is given in the S-Register description in section 0. SW release R300 ● ©2012 Telegesis (UK) Ltd - 17 - AT Command Manual (Rev 3.08)
Page 1 and 2: Telegesis TG-ETRXn-R308-AT-Commands
Page 3 and 4: R308 AT Commands 1 Introduction Thi
Page 5 and 6: R308 AT Commands of the module, the
Page 7 and 8: R308 AT Commands 2.2 Prompt Overvie
Page 9 and 10: R308 AT Commands 2.3.2 Non-ZigBee t
Page 11 and 12: R308 AT Commands Command Overview (
Page 13 and 14: R308 AT Commands +BLOAD - Enter The
Page 15: R308 AT Commands S - S-Register Acc
Page 19 and 20: R308 AT Commands +EN - Establish Pe
Page 21 and 22: R308 AT Commands +DASSL - Disassoci
Page 23 and 24: R308 AT Commands +RTABLE - Display
Page 25 and 26: R308 AT Commands +NODEDESC - Reques
Page 27 and 28: R308 AT Commands +SIMPLEDESC - Requ
Page 29 and 30: R308 AT Commands +SR - Set Source R
Page 31 and 32: R308 AT Commands +SN - Scan Network
Page 33 and 34: R308 AT Commands +CCHANGE - Change
Page 35 and 36: R308 AT Commands +BCAST - Transmit
Page 37 and 38: R308 AT Commands +UCAST - Transmit
Page 39 and 40: R308 AT Commands +SCAST - Transmit
Page 41 and 42: R308 AT Commands +SSINK - Search Fo
Page 43 and 44: R308 AT Commands +DMODE - Enter Dat
Page 45 and 46: R308 AT Commands +RDATAB - Send Bin
Page 47 and 48: R308 AT Commands +BSET - Set local
Page 49 and 50: R308 AT Commands +BIND - Create Bin
Page 51 and 52: R308 AT Commands 3 List of Error co
Page 53 and 54: R308 AT Commands 4 S-Registers Most
Page 55 and 56: R308 AT Commands With a few excepti
Page 57 and 58: R308 AT Commands S02 - Preferred PA
Page 59 and 60: R308 AT Commands S07 - Parent’s 1
Page 61 and 62: R308 AT Commands 4.3 S-Registers fo
Page 63 and 64: R308 AT Commands S0D - Device Infor
Page 65 and 66: R308 AT Commands S10 - Extended Fun
Page 67 and 68:
R308 AT Commands 4.4 I/O related S-
Page 69 and 70:
R308 AT Commands S14 - ETRX2: Pull-
Page 71 and 72:
R308 AT Commands S16 - Data Directi
Page 73 and 74:
R308 AT Commands S1A - Input Buffer
Page 75 and 76:
R308 AT Commands S1F - A/D1 Reading
Page 77 and 78:
R308 AT Commands 4.5 S-Registers De
Page 79 and 80:
R308 AT Commands S26 - Immediate Fu
Page 81 and 82:
R308 AT Commands S29 -Timer/Counter
Page 83 and 84:
R308 AT Commands S2D -Timer/Counter
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
R308 AT Commands S39 - Power Mode D
Page 91 and 92:
R308 AT Commands 4.6 Advanced Setti
Page 93 and 94:
R308 AT Commands S42 - Cluster ID f
Page 95 and 96:
R308 AT Commands S47 - Power Descri
Page 97 and 98:
R308 AT Commands S4C - Endpoint 2 O
Page 99 and 100:
R308 AT Commands 5 Build in Functio
Page 101 and 102:
R308 AT Commands Overview of Action
Page 103 and 104:
R308 AT Commands 7 ETRX357 Power Co
Page 105 and 106:
R308 AT Commands 8.2 Interpreting R
Page 107 and 108:
R308 AT Commands 10 Trademarks All
show all

R308 AT Command Manual - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?