R308 AT Command Manual - wless.ru

More documents

Recommendations

Info

R308 AT Commands +UNBIND – Delete Binding on Remote Device (ZDO) Write Command Response AT+UNBIND:,, SEQ:XX ,,, OK or ERROR: [,] The response indicates success or failure in sending this message. The acknowledgement as Delete Binding on a remote device with well as the actual response to this request will the target Node‟s EUI64, NodeID, follow as asynchronous prompts. or Address/Binding Table entry the Addressing mode as shown Prompt below Unbind:, The EUI64 of the Source The source Endpoint In case of an error an status other than 00 will be The Cluster ID on the source displayed Device is the Remote node‟s NodeID. The EUI64 or 16-bit multicast As with all unicasts after successful transmission ID, depending on the sequence number of the unicast is stated using Only in Mode 2: The destination the “SEQ:XX” prompt. When acknowledged (or not) endpoint the accompanying “ACK:XX” (or “NACK:XX”) prompt is displayed. Types: 1= Multicast Binding with Multicast ID Specified in 3= Unicast Binding with destination EUI64 in and destination EP in Note: Also the local node can be the target of this command (e.g. use address table entry FF as the address) Example AT+UNBIND,0000,3,000d6f000059474e,01, abcd,000D6F0000123456,01 Example SEQ:01 OK Unbind:0000,00 ACK:01 Note All parameters must have exactly the correct number of characters Use on All devices SW release R307 ● ©2012 Telegesis (UK) Ltd - 50 - AT Command Manual (Rev 3.08)
R308 AT Commands 3 List of Error codes 00 Everything OK - Success 01 Couldn’t poll Parent because of Timeout 02 Unknown command 04 Invalid S-Register 05 Invalid parameter 06 Recipient could not be reached 07 Message was not acknowledged 08 No sink known 09 Address Table entry is in use and cannot be modified 0A Message could not be sent 0B Local node is not sink 0C Too many characters 0E Background Scan in Progress (Please wait and try again) 0F Fatal error initialising the network 10 Error bootloading 12 Fatal error initialising the stack 18 Node has run out of Buffers 19 Trying to write read-only register 1A Data Mode Refused by Remote Node 1B Connection Lost in Data Mode 1C Remote node is already in Data Mode 20 Invalid password 25 Cannot form network 27 No network found 28 Operation cannot be completed if node is part of a PAN 2C Error leaving the PAN 2D Error scanning for PANs 33 No response from the remote bootloader 34 Target did not respond during cloning 35 Timeout occurred during xCASTB 39 MAC Transmit Queue is Full 6C Invalid Binding Index 70 Invalid Operation 72 More than 10 unicast messages were in flight at the same time 74 Message too long 80 ZDP Invalid Request Type 81 ZDP Device not Found 82 ZDP Invalid Endpoint 83 ZDP Not Active 84 ZDP Not Supported 85 ZDP Timeout 86 ZDP No Match 87 ZDP Table Full 88 ZDP No Entry 89 ZDP No Descriptor ©2012 Telegesis (UK) Ltd - 51 - AT Command Manual (Rev 3.08)
Page 1 and 2: Telegesis TG-ETRXn-R308-AT-Commands
Page 3 and 4: R308 AT Commands 1 Introduction Thi
Page 5 and 6: R308 AT Commands of the module, the
Page 7 and 8: R308 AT Commands 2.2 Prompt Overvie
Page 9 and 10: R308 AT Commands 2.3.2 Non-ZigBee t
Page 11 and 12: R308 AT Commands Command Overview (
Page 13 and 14: R308 AT Commands +BLOAD - Enter The
Page 15 and 16: R308 AT Commands S - S-Register Acc
Page 17 and 18: R308 AT Commands SALL - Remote S-Re
Page 19 and 20: R308 AT Commands +EN - Establish Pe
Page 21 and 22: R308 AT Commands +DASSL - Disassoci
Page 23 and 24: R308 AT Commands +RTABLE - Display
Page 25 and 26: R308 AT Commands +NODEDESC - Reques
Page 27 and 28: R308 AT Commands +SIMPLEDESC - Requ
Page 29 and 30: R308 AT Commands +SR - Set Source R
Page 31 and 32: R308 AT Commands +SN - Scan Network
Page 33 and 34: R308 AT Commands +CCHANGE - Change
Page 35 and 36: R308 AT Commands +BCAST - Transmit
Page 37 and 38: R308 AT Commands +UCAST - Transmit
Page 39 and 40: R308 AT Commands +SCAST - Transmit
Page 41 and 42: R308 AT Commands +SSINK - Search Fo
Page 43 and 44: R308 AT Commands +DMODE - Enter Dat
Page 45 and 46: R308 AT Commands +RDATAB - Send Bin
Page 47 and 48: R308 AT Commands +BSET - Set local
Page 49: R308 AT Commands +BIND - Create Bin
Page 53 and 54: R308 AT Commands 4 S-Registers Most
Page 55 and 56: R308 AT Commands With a few excepti
Page 57 and 58: R308 AT Commands S02 - Preferred PA
Page 59 and 60: R308 AT Commands S07 - Parent’s 1
Page 61 and 62: R308 AT Commands 4.3 S-Registers fo
Page 63 and 64: R308 AT Commands S0D - Device Infor
Page 65 and 66: R308 AT Commands S10 - Extended Fun
Page 67 and 68: R308 AT Commands 4.4 I/O related S-
Page 69 and 70: R308 AT Commands S14 - ETRX2: Pull-
Page 71 and 72: R308 AT Commands S16 - Data Directi
Page 73 and 74: R308 AT Commands S1A - Input Buffer
Page 75 and 76: R308 AT Commands S1F - A/D1 Reading
Page 77 and 78: R308 AT Commands 4.5 S-Registers De
Page 79 and 80: R308 AT Commands S26 - Immediate Fu
Page 81 and 82: R308 AT Commands S29 -Timer/Counter
Page 83 and 84: R308 AT Commands S2D -Timer/Counter
Page 89 and 90: R308 AT Commands S39 - Power Mode D
Page 91 and 92: R308 AT Commands 4.6 Advanced Setti
Page 93 and 94: R308 AT Commands S42 - Cluster ID f
Page 95 and 96: R308 AT Commands S47 - Power Descri
Page 97 and 98: R308 AT Commands S4C - Endpoint 2 O
Page 99 and 100: R308 AT Commands 5 Build in Functio
Page 101 and 102:
R308 AT Commands Overview of Action
Page 103 and 104:
R308 AT Commands 7 ETRX357 Power Co
Page 105 and 106:
R308 AT Commands 8.2 Interpreting R
Page 107 and 108:
R308 AT Commands 10 Trademarks All
show all

R308 AT Command Manual - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?