R308 AT Command Manual - wless.ru

More documents

Recommendations

Info

R308 AT Commands S09 – Trust Centre Link Key Description The link key which can be written using the password. The default password for R3xx is “password”. Operations W LOCAL W REMOTE Write operation ATS09=: ATREMS:,09=: Becomes effective When Joining or establishing a PAN Range From 0 to 2 128 -1 The 128-bit trust centre link key in hexadecimal representation (32 characters). When set to all 0s (default) a random trust centre link key is generated when establishing a PAN. Storage Factory Default Non Volatile 00000000000000000000000000000000 SW release R300 ● ©2012 Telegesis (UK) Ltd - 60 - AT Command Manual (Rev 3.08)
R308 AT Commands 4.3 S-Registers for Module Setup S0A – Main Function Description Defines the behaviour of the Device. Parameters XXXX Operations R/W LOCAL R/W REMOTE Becomes effective When joining or establishing a PAN (bits F-D) When PWM is next enabled (bit C) Instantly (bits B-0) Write operation ATS0A=XXXX: ATREMS:,0A=XXXX: Notes For security reasons this register is password protected. The default password for R3xx is “password”. See section 0 regarding secure networks To block joining, set either bit 5 on the trust centre or bit 0 on every node. Built-in function 0017 only overrides bit 0 An End Device (not Sleepy or Mobile) is primarily to let a ZigBee PRO device join a ZigBee 2006 PAN. An SED or MED is the more usual choice Where XXXX represents a 16-bit hexadecimal number. Range 0000 to FFFF Bit E-F: Device Selection Bit F Bit E Device Type 0 0 Router (FFD) 1 0 End Device 0 1 Sleepy End Device 1 1 Mobile End Device Bit D: Set: If a router, do not route any messages Bit C: Prescale PWM clock to reduce frequency by 256 Bit B: Set: Allows Endpoint 2 to reply to ZDO endpoint queries Bit A: Set: When joining don‟t ask for Trust Centre link key Bit 9: Set: Don‟t use central Trust Centre (distributed TC Mode) Bit 8: Set: Use Pre-Configured Trust Centre Link Key when joining Bit 7: Set: Trust centre uses hashed link key Bit 6: Reserved Bit 5: Set: Don‟t allow nodes to join (TC setting) Bit 4: Set: Send Network key encrypted with the link key to nodes joining Storage Non-Volatile Bit 3: Set: Don‟t allow nodes to re-join unsecured Bit 2: Set: Send Network key encrypted with the link key to nodes re-joining unsecured Bit 1: Reserved Bit 0: Set: Don‟t allow other nodes to join the network via this node Factory Default 0000 SW release R301 ● ©2012 Telegesis (UK) Ltd - 61 - AT Command Manual (Rev 3.08)
Page 1 and 2:
Telegesis TG-ETRXn-R308-AT-Commands
Page 3 and 4:
R308 AT Commands 1 Introduction Thi
Page 5 and 6:
R308 AT Commands of the module, the
Page 7 and 8:
R308 AT Commands 2.2 Prompt Overvie
Page 9 and 10: R308 AT Commands 2.3.2 Non-ZigBee t
Page 11 and 12: R308 AT Commands Command Overview (
Page 13 and 14: R308 AT Commands +BLOAD - Enter The
Page 15 and 16: R308 AT Commands S - S-Register Acc
Page 17 and 18: R308 AT Commands SALL - Remote S-Re
Page 19 and 20: R308 AT Commands +EN - Establish Pe
Page 21 and 22: R308 AT Commands +DASSL - Disassoci
Page 23 and 24: R308 AT Commands +RTABLE - Display
Page 25 and 26: R308 AT Commands +NODEDESC - Reques
Page 27 and 28: R308 AT Commands +SIMPLEDESC - Requ
Page 29 and 30: R308 AT Commands +SR - Set Source R
Page 31 and 32: R308 AT Commands +SN - Scan Network
Page 33 and 34: R308 AT Commands +CCHANGE - Change
Page 35 and 36: R308 AT Commands +BCAST - Transmit
Page 37 and 38: R308 AT Commands +UCAST - Transmit
Page 39 and 40: R308 AT Commands +SCAST - Transmit
Page 41 and 42: R308 AT Commands +SSINK - Search Fo
Page 43 and 44: R308 AT Commands +DMODE - Enter Dat
Page 45 and 46: R308 AT Commands +RDATAB - Send Bin
Page 47 and 48: R308 AT Commands +BSET - Set local
Page 49 and 50: R308 AT Commands +BIND - Create Bin
Page 51 and 52: R308 AT Commands 3 List of Error co
Page 53 and 54: R308 AT Commands 4 S-Registers Most
Page 55 and 56: R308 AT Commands With a few excepti
Page 57 and 58: R308 AT Commands S02 - Preferred PA
Page 59: R308 AT Commands S07 - Parent’s 1
Page 63 and 64: R308 AT Commands S0D - Device Infor
Page 65 and 66: R308 AT Commands S10 - Extended Fun
Page 67 and 68: R308 AT Commands 4.4 I/O related S-
Page 69 and 70: R308 AT Commands S14 - ETRX2: Pull-
Page 71 and 72: R308 AT Commands S16 - Data Directi
Page 73 and 74: R308 AT Commands S1A - Input Buffer
Page 75 and 76: R308 AT Commands S1F - A/D1 Reading
Page 77 and 78: R308 AT Commands 4.5 S-Registers De
Page 79 and 80: R308 AT Commands S26 - Immediate Fu
Page 81 and 82: R308 AT Commands S29 -Timer/Counter
Page 83 and 84: R308 AT Commands S2D -Timer/Counter
Page 89 and 90: R308 AT Commands S39 - Power Mode D
Page 91 and 92: R308 AT Commands 4.6 Advanced Setti
Page 93 and 94: R308 AT Commands S42 - Cluster ID f
Page 95 and 96: R308 AT Commands S47 - Power Descri
Page 97 and 98: R308 AT Commands S4C - Endpoint 2 O
Page 99 and 100: R308 AT Commands 5 Build in Functio
Page 101 and 102: R308 AT Commands Overview of Action
Page 103 and 104: R308 AT Commands 7 ETRX357 Power Co
Page 105 and 106: R308 AT Commands 8.2 Interpreting R
Page 107 and 108: R308 AT Commands 10 Trademarks All
show all

R308 AT Command Manual - wless.ru

Create successful ePaper yourself

Delete template?

Save as template?