R308 AT Command Manual - wless.ru

More documents

Recommendations

Info

R308 AT Commands Throughout this document, only the responses and prompts are presented, are omitted intentionally. Sequences of AT commands in a single line are not supported. The ETRX2 and ETRX357 feature a 128-byte FIFO to buffer incoming characters from the host processor, which is sufficient to hold even the longest possible command. The ETRX357 features a 256 byte FIFO buffer for incoming radio messages, which allows rapid reception of multiple messages without loss of characters. To prevent a buffer overflow XON/XOFF handshaking is used. Optional hardware handshaking can be enabled as described in the register description of S12 in section 0. Read Command ATXXX Write Command ATXXX= Execute Command ATXXX Commands ending with a „‟ return the currently set value of the parameter or parameters This command sets user-definable parameters as indicated by the „=‟ sign. This command executes routines of the module and returns parameters Table 1: Types of AT commands When bit 7 of S12 is set each individual reply or prompt is additionally started with the STX and ended with the ETX character to aid the interpretation of the incoming strings on a host processor. 2.1 Parameters Each parameter must be entered in the correct format for any of the AT commands to execute correctly. Optional parameters are marked with square brackets […]. XX 8-bit hexadecimal number. Valid characters are 0-9, a-f and A-F XXXX 16-bit hexadecimal number. Valid characters are 0-9, a-f and A-F n Number from 0-9 s Sign b Bit (0 or 1) c character 16-bit hexadecimal PAN ID (0000 to FFFF) 64-bit hexadecimal extended PAN ID decimal channel (802.15.4 channel 11-26) 8 character password 64-bit IEEE 802.15.4 address in hexadecimal 32-bit hexadecimal number representing the reading of S1A Custom Data A list of 16 bit cluster identifiers in hexadecimal representation The Firmware Revision Number Table 2: Different formats of parameters ©2012 Telegesis (UK) Ltd - 6 - AT Command Manual (Rev 3.08)
R308 AT Commands 2.2 Prompt Overview The following prompts can show up during the operation of the ETRXn modules. Most of the prompts can be disabled using register S0E and S0F. Prompt Overview OK OK terminator ERROR:XX Error number XX occurred ACK:XX Acknowledgement for message XX was received NACK:XX Acknowledgement for message XX was not received SR:XX,,,… Route Record Message received BCAST:[,]XX= A Broadcast with XX characters has been received MCAST:[,]XX= A Multicast with XX characters has been received UCAST:[,]XX= A Unicast with XX characters has been received SDATA:[,],,,, A data message has been received at the sink. , ADC data is A/D1 & A/D2 or ADC0 & ADC1 FN0130:[],,, ,,[],[], [],[] A data message has been received at the sink. The number of ADC data fields depends on how many ADCs are activated at the sender FFD:, A router announcing itself SED:, A sleepy end device announcing itself MED:, A mobile sleepy end device announcing itself ZED:, NEWNODE: ,, LeftPAN LostPAN JPAN:,, SINK:, ADSK:, SREAD:,,, [=] SWRITE:,, An end device announcing itself Shown on Coordinator: New node has been given permission to join the PAN. NB joining is not complete until an “FFD” prompt or similar is received Local Node has left the PAN End Device has lost contact with Parent Local Node has joined PAN with given parameters Selected new Sink Received Sink Advertisement Reply to a remote S Register Read operation Reply to a remote S Register Write operation ©2012 Telegesis (UK) Ltd - 7 - AT Command Manual (Rev 3.08)
Page 1 and 2: Telegesis TG-ETRXn-R308-AT-Commands
Page 3 and 4: R308 AT Commands 1 Introduction Thi
Page 5: R308 AT Commands of the module, the
Page 9 and 10: R308 AT Commands 2.3.2 Non-ZigBee t
Page 11 and 12: R308 AT Commands Command Overview (
Page 13 and 14: R308 AT Commands +BLOAD - Enter The
Page 15 and 16: R308 AT Commands S - S-Register Acc
Page 17 and 18: R308 AT Commands SALL - Remote S-Re
Page 19 and 20: R308 AT Commands +EN - Establish Pe
Page 21 and 22: R308 AT Commands +DASSL - Disassoci
Page 23 and 24: R308 AT Commands +RTABLE - Display
Page 25 and 26: R308 AT Commands +NODEDESC - Reques
Page 27 and 28: R308 AT Commands +SIMPLEDESC - Requ
Page 29 and 30: R308 AT Commands +SR - Set Source R
Page 31 and 32: R308 AT Commands +SN - Scan Network
Page 33 and 34: R308 AT Commands +CCHANGE - Change
Page 35 and 36: R308 AT Commands +BCAST - Transmit
Page 37 and 38: R308 AT Commands +UCAST - Transmit
Page 39 and 40: R308 AT Commands +SCAST - Transmit
Page 41 and 42: R308 AT Commands +SSINK - Search Fo
Page 43 and 44: R308 AT Commands +DMODE - Enter Dat
Page 45 and 46: R308 AT Commands +RDATAB - Send Bin
Page 47 and 48: R308 AT Commands +BSET - Set local
Page 49 and 50: R308 AT Commands +BIND - Create Bin
Page 51 and 52: R308 AT Commands 3 List of Error co
Page 53 and 54: R308 AT Commands 4 S-Registers Most
Page 55 and 56: R308 AT Commands With a few excepti
Page 57 and 58:
R308 AT Commands S02 - Preferred PA
Page 59 and 60:
R308 AT Commands S07 - Parent’s 1
Page 61 and 62:
R308 AT Commands 4.3 S-Registers fo
Page 63 and 64:
R308 AT Commands S0D - Device Infor
Page 65 and 66:
R308 AT Commands S10 - Extended Fun
Page 67 and 68:
R308 AT Commands 4.4 I/O related S-
Page 69 and 70:
R308 AT Commands S14 - ETRX2: Pull-
Page 71 and 72:
R308 AT Commands S16 - Data Directi
Page 73 and 74:
R308 AT Commands S1A - Input Buffer
Page 75 and 76:
R308 AT Commands S1F - A/D1 Reading
Page 77 and 78:
R308 AT Commands 4.5 S-Registers De
Page 79 and 80:
R308 AT Commands S26 - Immediate Fu
Page 81 and 82:
R308 AT Commands S29 -Timer/Counter
Page 83 and 84:
R308 AT Commands S2D -Timer/Counter
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
R308 AT Commands S39 - Power Mode D
Page 91 and 92:
R308 AT Commands 4.6 Advanced Setti
Page 93 and 94:
R308 AT Commands S42 - Cluster ID f
Page 95 and 96:
R308 AT Commands S47 - Power Descri
Page 97 and 98:
R308 AT Commands S4C - Endpoint 2 O
Page 99 and 100:
R308 AT Commands 5 Build in Functio
Page 101 and 102:
R308 AT Commands Overview of Action
Page 103 and 104:
R308 AT Commands 7 ETRX357 Power Co
Page 105 and 106:
R308 AT Commands 8.2 Interpreting R
Page 107 and 108:
R308 AT Commands 10 Trademarks All
show all

R308 AT Command Manual - wless.ru

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?