PXR3 Instruction Manual - Coulton Instrumentation

More documents

Recommendations

Info

Parity for communication (Setting range: 0 to 2) (Option)[Description]• This parameter sets the parity for communications.The baud rate is fixed at 9600bps.: Odd parity: Even parity: No parity[Setting example] Setting the even parityDisplayPV indicationSV indicationPV indicationPress and hold the SEL key for five seconds.will be displayed.Press the key to display .Press the SEL key once.The current setting ( ) will be displayed.Operating procedurePress the or keys to flicker and to display .Press the SEL key once. will be displayed and the even parity will be registered for .However, it does not switch to the even parity at this point.(Repeat the procedure from 3 to 5 to check the set value.)Power off the PXR3, and then on. The even parity is set now.If you want to display the operation status, press and hold the SEL key for two seconds.The SV will be displayed on the display area.If unoperated state continues, the PV will be displayed.65
Input type for PYP (Setting range: 0 to 7, 32 to 47) (Option)[Description]• When the Color Touch-Operation Unit (Model: PYP)made by Fuji Electric is connected to the PXR, this parametermakes the PYP recognize the measured range.• When setting the same temperature range that is set inthe input range, P-SL, and P-SU of the PXR, the readingsbetween the PXR and PYP are met.Set value000102030405060732333435363738394041424344454647Input typeResistance bulbJISIECThermocouplePt100JJKKKRBTTEESNUWRe5 · 26PLIITemperature range(°C)0 to 150°C0 to 300°C0 to 500°C0 to 600°C-50 to 100°C-100 to 200°C-150 to 600°C-150 to 850°C0 to 400°C0 to 800°C0 to 400°C0 to 800°C0 to 1200°C0 to 1600°C0 to 1800°C-199.9 to 200°C-150 to 400°C0 to 800°C-199.9 to 800°C0 to 1600°C0 to 1300°C-199.9 to 400°C0 to 2300°C0 to 1300°C[Setting example] Setting the input range of the PXR3 to thermocouple BDisplayPV indicationPress and hold the SEL key for five seconds.will be displayed.Press the key to display .Press the SEL key once.The current setting ( ) will be displayed.Operating procedurePress the or keys to flicker and to display .Press the SEL key once. will be displayed and (Thermocouple B) will be registered for the input range.After that, PYP will recognize the input range of the PXR3 as thermocouple B ( 0 to 1800˚C).SV indicationPV indication(Repeat the procedure from 3 to 5 to check the set value.)If you want to display the operation status, press and hold theThe SV will be displayed on the display area.If unoperated state continues, the PV will be displayed.SEL key for two seconds.66
Page 1 and 2:
Instruction ManualMicro-controller
Page 3 and 4:
Safety PrecautionsBefore using this
Page 5 and 6:
• If there is a danger of a serio
Page 7 and 8:
Standard : Vertical mounting, flush
Page 9 and 10:
IndexConfirming type specificationI
Page 11 and 12:
2 WiringTerminal Connection Diagram
Page 13 and 14:
4 Display and operationStandby mode
Page 15 and 16:
Operation/Standby modeSV indication
Page 17 and 18:
6 Functions6-1 ON/OFF control• At
Page 19 and 20:
6-3 Self-tuning1) At power on, chan
Page 21 and 22:
6-4 Alarm function (option)1) Kinds
Page 23 and 24:
6-5 Ramp/soak function [option]1. F
Page 25 and 26:
6-7 Digital input (DI function) [op
Page 27 and 28:
6-9 Retransmission function [option
Page 29 and 30:
2Setting ofthe algorithm* Read if t
Page 31 and 32:
[Table 1] Input type codeParameter
Page 33 and 34:
[Table 4] Control output action mod
Page 35 and 36:
SpecificationPower voltage:100 (-15
Page 37 and 38:
Table of Contents1 Part Names and F
Page 39 and 40:
PXRdigit Specification Note45678910
Page 41 and 42:
2 OperationsThis chapter explains h
Page 43 and 44:
Parameterdisplay symbolParameter na
Page 45 and 46:
Parameterdisplay symbolParameter na
Page 47 and 48:
2-3 Parameter functions and method
Page 49 and 50: Ramp-soak control (Settings: oFF/rU
Page 51 and 52: Auto-tuning function (Settings: 0/1
Page 53 and 54: Setting alarm 1 and 2Upper limit of
Page 55 and 56: w Second block parametersProportion
Page 57 and 58: Derivative time (Setting range: 0.0
Page 59 and 60: Cooling-side proportional band coef
Page 61 and 62: Output offset value (Setting range:
Page 63 and 64: [Self-tuning]1 Function:With the se
Page 65 and 66: 7 Reference [About the self-tuning
Page 67 and 68: HYS (Hysteresis) mode at ON/OFF con
Page 69 and 70: Cycle time of control output 2 (Coo
Page 71 and 72: Setting lower limit of the measurin
Page 73 and 74: Decimal point position (Settings: 0
Page 75 and 76: SV offset (Setting range: -50 to 50
Page 77 and 78: , Alarm types (Setting range: 0 to
Page 79 and 80: • Alarm codes with dual set value
Page 81 and 82: Ramp-soak status display (Display o
Page 83 and 84: • The segment in which both the r
Page 85 and 86: SV (Setting value) lower limiter (S
Page 87 and 88: [Setting example] Setting the delay
Page 89 and 90: , Options of alarm 1 and 2 (Setting
Page 91 and 92: [Description], Upper and lower limi
Page 93 and 94: , Output value display (Display onl
Page 95 and 96: Adjusting the PV (Measured value) d
Page 97 and 98: Starting the auto-tuning (DI functi
Page 99: Station No. for communication (Sett
Page 103 and 104: Retransmission base scale (Setting
Page 105 and 106: 3 TroubleshootingThis section expla
Page 107 and 108: Index72AAdjusting the PV display (0
Page 109: Safety Precaution● Before using t
show all

PXR3 Instruction Manual - Coulton Instrumentation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?