PXR3 Instruction Manual - Coulton Instrumentation

More documents

Recommendations

Info

, The time of ON-delay alarm or timer function (Setting range: 0 to 9999 seconds)(Option)[Description]ON-delay alarm• The timer display function shows the remaining time of• With this function, the alarm relay is closed after the predetermineddelay time. (See operation q shown in the • The set time is counted down while the ON or OFF timer istimers 1 and 2.figure below.)activated.• In case the cause of the alarm is solved within the delay • While the ON timer is activated, the alarm relay is closedtime, the alarm relay is not closed. (See operation e shown when the remaining time is 0. While the OFF timer is activated,the alarm relay is opened when the remaining time is 0.in the figure below.)• The alarm relay is opened regardless of this parameter.(See operation w shown in the figure below.)AlarmoperationAlarm relayoperation undernormal conditionsONOFFONOFFAlarm relay ONoperation duringON-delay OFFq Delay w esetting time• In case the alarm is set to OFF during standby, the ONdelayoperation performs again when returning to RUN.• When the delay time is changed during ON-delay operation,the alarm is activated in the changed delay time.Timer function• When the ON-delay timer is selected, the relay is closed inthe set time after DI input is set to ON. While the DI inputstays OFF, the timer cannot be activated.• When the OFF-delay timer is selected, the timer cannotbe activated while the DI input is set to ON. The relayis closed in the set time after DI input is set to OFF.• When the ON/OFF-delay timer is selected, the timer isactivated while the DI input stays either ON or OFF.• ON-delay timer operationTONDI inputOFFRelay output ONalarm LEDOFFDe-energizedoutput LEDONOFFSet value: TTimer display0• OFF-delay timer operationDI inputONOFFRelay output ONalarm LEDOFFInvert outputLEDONOFFDisplays the remainingtime (seconds)TT:dLYn(n=1 / 2 / 3)Set value: TTimer display0T:dLYn(n=1 / 2 / 3)51
[Setting example] Setting the delay time for ON-delay alarm to 30 secondsDisplayPV indicationSV indicationPV indication1.2.3.4.5.6.Press and hold the SEL key for five seconds.will be displayed.Press the key to display .Press the SEL key once.The current setting ( ) will be displayed.Operating procedurePress the or keys to flicker and to display .Press the SEL key once. will be displayed and seconds will be registered for .After that, the controller will operate with being 30 seconds.(Repeat the procedure from 3 to 5 to check the set value.)If you want to display the operation status, press and hold the SEL key for two seconds.The SV will be displayed on the display area.If unoperated state continues, the PV will be displayed.52
Page 1 and 2:
Instruction ManualMicro-controller
Page 3 and 4:
Safety PrecautionsBefore using this
Page 5 and 6:
• If there is a danger of a serio
Page 7 and 8:
Standard : Vertical mounting, flush
Page 9 and 10:
IndexConfirming type specificationI
Page 11 and 12:
2 WiringTerminal Connection Diagram
Page 13 and 14:
4 Display and operationStandby mode
Page 15 and 16:
Operation/Standby modeSV indication
Page 17 and 18:
6 Functions6-1 ON/OFF control• At
Page 19 and 20:
6-3 Self-tuning1) At power on, chan
Page 21 and 22:
6-4 Alarm function (option)1) Kinds
Page 23 and 24:
6-5 Ramp/soak function [option]1. F
Page 25 and 26:
6-7 Digital input (DI function) [op
Page 27 and 28:
6-9 Retransmission function [option
Page 29 and 30:
2Setting ofthe algorithm* Read if t
Page 31 and 32:
[Table 1] Input type codeParameter
Page 33 and 34:
[Table 4] Control output action mod
Page 35 and 36: SpecificationPower voltage:100 (-15
Page 37 and 38: Table of Contents1 Part Names and F
Page 39 and 40: PXRdigit Specification Note45678910
Page 41 and 42: 2 OperationsThis chapter explains h
Page 43 and 44: Parameterdisplay symbolParameter na
Page 45 and 46: Parameterdisplay symbolParameter na
Page 47 and 48: 2-3 Parameter functions and method
Page 49 and 50: Ramp-soak control (Settings: oFF/rU
Page 51 and 52: Auto-tuning function (Settings: 0/1
Page 53 and 54: Setting alarm 1 and 2Upper limit of
Page 55 and 56: w Second block parametersProportion
Page 57 and 58: Derivative time (Setting range: 0.0
Page 59 and 60: Cooling-side proportional band coef
Page 61 and 62: Output offset value (Setting range:
Page 63 and 64: [Self-tuning]1 Function:With the se
Page 65 and 66: 7 Reference [About the self-tuning
Page 67 and 68: HYS (Hysteresis) mode at ON/OFF con
Page 69 and 70: Cycle time of control output 2 (Coo
Page 71 and 72: Setting lower limit of the measurin
Page 73 and 74: Decimal point position (Settings: 0
Page 75 and 76: SV offset (Setting range: -50 to 50
Page 77 and 78: , Alarm types (Setting range: 0 to
Page 79 and 80: • Alarm codes with dual set value
Page 81 and 82: Ramp-soak status display (Display o
Page 83 and 84: • The segment in which both the r
Page 85: SV (Setting value) lower limiter (S
Page 89 and 90: , Options of alarm 1 and 2 (Setting
Page 91 and 92: [Description], Upper and lower limi
Page 93 and 94: , Output value display (Display onl
Page 95 and 96: Adjusting the PV (Measured value) d
Page 97 and 98: Starting the auto-tuning (DI functi
Page 99 and 100: Station No. for communication (Sett
Page 101 and 102: Input type for PYP (Setting range:
Page 103 and 104: Retransmission base scale (Setting
Page 105 and 106: 3 TroubleshootingThis section expla
Page 107 and 108: Index72AAdjusting the PV display (0
Page 109: Safety Precaution● Before using t
show all

PXR3 Instruction Manual - Coulton Instrumentation

Create successful ePaper yourself

Delete template?

Save as template?