- Page 1 and 2:
Instruction ManualMicro-controller
- Page 3 and 4:
Safety PrecautionsBefore using this
- Page 5 and 6:
• If there is a danger of a serio
- Page 7 and 8:
Standard : Vertical mounting, flush
- Page 9 and 10:
IndexConfirming type specificationI
- Page 11 and 12:
2 WiringTerminal Connection Diagram
- Page 13 and 14:
4 Display and operationStandby mode
- Page 15 and 16:
Operation/Standby modeSV indication
- Page 17 and 18:
6 Functions6-1 ON/OFF control• At
- Page 19 and 20:
6-3 Self-tuning1) At power on, chan
- Page 21 and 22:
6-4 Alarm function (option)1) Kinds
- Page 23 and 24:
6-5 Ramp/soak function [option]1. F
- Page 25 and 26:
6-7 Digital input (DI function) [op
- Page 27 and 28:
6-9 Retransmission function [option
- Page 29 and 30:
2Setting ofthe algorithm* Read if t
- Page 31 and 32:
[Table 1] Input type codeParameter
- Page 33 and 34:
[Table 4] Control output action mod
- Page 35 and 36:
SpecificationPower voltage:100 (-15
- Page 37 and 38:
Table of Contents1 Part Names and F
- Page 39 and 40:
PXRdigit Specification Note45678910
- Page 41 and 42:
2 OperationsThis chapter explains h
- Page 43 and 44:
Parameterdisplay symbolParameter na
- Page 45 and 46:
Parameterdisplay symbolParameter na
- Page 47 and 48:
2-3 Parameter functions and method
- Page 49 and 50:
Ramp-soak control (Settings: oFF/rU
- Page 51 and 52:
Auto-tuning function (Settings: 0/1
- Page 53 and 54:
Setting alarm 1 and 2Upper limit of
- Page 55 and 56:
w Second block parametersProportion
- Page 57 and 58: Derivative time (Setting range: 0.0
- Page 59 and 60: Cooling-side proportional band coef
- Page 61 and 62: Output offset value (Setting range:
- Page 63 and 64: [Self-tuning]1 Function:With the se
- Page 65 and 66: 7 Reference [About the self-tuning
- Page 67 and 68: HYS (Hysteresis) mode at ON/OFF con
- Page 69 and 70: Cycle time of control output 2 (Coo
- Page 71 and 72: Setting lower limit of the measurin
- Page 73 and 74: Decimal point position (Settings: 0
- Page 75 and 76: SV offset (Setting range: -50 to 50
- Page 77 and 78: , Alarm types (Setting range: 0 to
- Page 79 and 80: • Alarm codes with dual set value
- Page 81 and 82: Ramp-soak status display (Display o
- Page 83 and 84: • The segment in which both the r
- Page 85 and 86: SV (Setting value) lower limiter (S
- Page 87 and 88: [Setting example] Setting the delay
- Page 89 and 90: , Options of alarm 1 and 2 (Setting
- Page 91 and 92: [Description], Upper and lower limi
- Page 93 and 94: , Output value display (Display onl
- Page 95 and 96: Adjusting the PV (Measured value) d
- Page 97 and 98: Starting the auto-tuning (DI functi
- Page 99 and 100: Station No. for communication (Sett
- Page 101 and 102: Input type for PYP (Setting range:
- Page 103 and 104: Retransmission base scale (Setting
- Page 105 and 106: 3 TroubleshootingThis section expla
- Page 107: Index72AAdjusting the PV display (0