PXR3 Instruction Manual - Coulton Instrumentation

[Table 3] Alarm action type codeParameter : ,· Standard alarm code· Alarm code with dual set valueALM1 ALM2 Alarm type Action diagram ALM1 ALM2 Alarm type Action diagramAbsolutevaluealarmDeviationalarmZonealarm· Timer codeTimer0 0 No alarm PV1 1 High alarmHigh alarm(with hold)Low alarm(with hold)AL1AL22 2 Low alarmAL1PVAL23 34 45 5 High alarm6 67 78 89 910 1011 11Low alarmHigh/LowalarmHigh alarm(with hold)Low alarm(with hold)High/Lowalarm(with hold)High/Lowdeviation alarm(ALM1/2 independentaction)SVAL1AL2AL1AL2AL1AL2High/Low- 12 PVabsolute alarm AL2AL1- 13- 14- 15High/Lowdeviation alarmHigh absolute/Low deviationalarmHigh deviation/Low absolutealarmSVAL2AL1AL2AL1AL2AL1AL2AL1AL2AL2SVSVSVSVAL2SVSVAL1AL2AL1AL2AL1AL2AL1AL2AL1AL2AL1AL1ALM1 ALM2 Alarm type Action diagram32 32 ON delay timer33 33 OFF delay timer34 34 ON/OFFdelay timerDIOUTDIOUTDIOUTdLY1dLY2dLY1dLY2dLY1dLY2SVSVAL1dLY1dLY2PVPVPVPVPVPVPVPVPVPVPVPVPVHigh/LowlimitalarmZonealarmPointNote) · When alarm action type code is changed, alarm set value may also become different from previ oussettings.Please check these parameters, turn off the power once, and then re-start the controller, before startingcontrol.· When selecting No.12 to 15, setting in ALM2, dLY2, and A2hy are effective, and output to the AL2relay.– 32 –16 1617 1718 1819 1920 2021 2122 2223 2324 2425 2526 2627 2728 2829 2930 3031 31High/Lowabsolute alarmHigh/Lowdeviation alarmHigh absolute/Low deviationalarmHigh deviation/Low absolutealarmHigh/Lowabsolute alarm(with hold)High/Lowdeviation alarm(with hold)High absolute/Low deviationalarm (with hold)High deviation/Low absolutealarm (with hold)High/Lowabsolute alarmHigh/Lowdeviation alarmHigh absolute/Low deviationalarmHigh deviation/Low absolutealarmHigh/Lowabsolute alarm(with hold)High/Lowdeviation alarm(with hold)High absolute/Low deviationalarm (with hold)High deviation/Low absolutealarm (with hold)A1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LSVA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-LA2-LA1-HA2-HA1-HA2-HSV A1-HA2-HA1-HA2-HSVSVA1-LA2-LA1-HA2-HA1-HA2-HSVA1-HSVA2-HA1-HA2-HSVSVA1-LA2-LA1-HA2-HA1-HA2-HA1-HSVA2-HA1-HA2-HSVA1-HA2-HA1-HA2-HSV A1-HA2-HA1-HA2-HWhat is alarm with hold?The alarm is not turned ON immediately even when the processvalue is in the alarm band. It turns ON when it goes out the alarmband and enters again.Power ONLower limit alarmLower limit alarm(with hold)Power OFFSVPV (process value)offoffonPower ONoffononoffoffPVPVPVPVPVPVPVPVPVPVPVPVPVPVPVPVPeriod where lowerlimit alarm is output