NetEx EFT213 Reference Manual Rel 5.4

More documents

Recommendations

Info

ExamplesIf you desire to leave NetEx/eFT and return to your local system’s command line interpreter, you would type:eFT> quitREADYAt this point you should receive the prompt you normally receive from your system’s command line interpreter(e.g., READY).If you desire to leave NetEx/eFT and return an Error status to your local system, you would type:eFT> quit errorREADYAt this point you should receive the prompt you normally receive from your system’s command line interpreter(e.g., READY).Related TopicsDISCONNECT CommandEXIT CommandPage 142 Command Descriptions REF-eFT213-R5.4-08
RECEIVE CommandDescriptionThe RECEIVE command receives the source file or data set from the current active remote host and saves itas the destination file or data set on the local host.If the destination data set specification is not a fully qualified data set name (i.e., if it is not enclosed in singlequotes) or DD name specification, the data set name is prefixed with the current default value ofDIRECTORY (which is equivalent to TSOPREFIX) on the destination z/OS host. Similarly, if the source filespecification is not fully qualified (if connected to another z/OS host), or if no path to the file is specified (i.e.,if a file name is given without a directory on non-z/OS hosts), the file is prefixed with the default value ofDIRECTORY on the source z/OS host. In either case, DIRECTORY is used as the path to the file or data setname.If the destination parameter is not specified at all, a data set name will be constructed from the source filename and will be prefixed with the value of DIRECTORY (TSOPREFIX) on the destination z/OS host. Thesource file name and the extension will both be truncated to eight characters if needed.NetEx/eFT for IBM z/OS will transfer into either a sequential or a partitioned data set. If a member name issupplied as part of the data set name, NetEx/eFT will assume the data set is partitioned, and either create anew partitioned data set and member, or create/replace the member in an existing partitioned data set. If amember name is supplied and the existing destination data set is sequential, an error message is returned. Ifno member name is supplied and the existing destination data set is partitioned, NetEx/eFT will build a membername from the source file (data set) name and create or replace the member. Otherwise, NetEx/eFT willcreate a new sequential data set or replace (overwrite) an existing sequential data set.Experienced z/OS users may also use a DD Name (Data Definition name) in place of an z/OS data set nameso long as the DD Name references an allocated data set with valid characteristics for the particular file transfer.The syntax for specifying a DD name is DD:ddname or DD:ddname(member). z/OS secondary spacerequests will not be processed if the member name is provided on a DD specification.The source file name may include the NetEx/eFT wildcard characters * and ?. See “Source Wildcard Supportfor IBM z/OS File Transfers” on page 54 and “Destination Wildcard Support for IBM z/OS File Transfers”on page 56 for more details.FormatCommand Qualifier ParameterRECeive [-qualifiers] source [destination]Where:RECeive-qualifierssourcedestination(required) the verb for this command. The minimum spelling is REC.(optional) the qualifiers that apply to the RECEIVE command. Refer to “File Handling UnderIBM z/OS NetEx/eFT” on page 41 for a description of the RECEIVE command qualifiers.See also the file handling section of the remote host manual for details on qualifiers supported.(required) the file specification for the file on the remote host that you intend to receive.(optional) the file specification for the new file that is to be created on the local host.REF-eFT213-R5.4-08 Command Descriptions Page 143
Page 1 and 2:
eFT213NetEx/eFT for z/OS SystemsRel
Page 3:
or, by visiting our web site at:htt
Page 6 and 7:
Notice to the ReaderThe material co
Page 8 and 9:
Glossaryasynchronous: A class of da
Page 10:
Page xREF-eFT213-R5.4-08
Page 14 and 15:
Related Topics ....................
Page 16 and 17:
Description .......................
Page 18 and 19:
Examples ..........................
Page 23:
IntroductionNetEx/eFT OverviewThe N
Page 26 and 27:
eFT: Remote: Login failed (SI693-80
Page 28 and 29:
ultra5> local directoryIN CATALOG:U
Page 30 and 31:
Page 8 Introduction REF-eFT213-R5.4
Page 32 and 33:
Examples:-HOMEdir-OUTput-ROOTdir-SE
Page 34 and 35:
SEND.) Any aliases defined in these
Page 36 and 37:
eFT> set input echoFor Boolean qual
Page 38 and 39:
This will prevent general NetEx/eFT
Page 40 and 41:
Terminating a NetEx/eFT SessionTo e
Page 42 and 43:
eFT> show localeFT:eFT:* COPYRight
Page 44 and 45:
eFT> loginHostname? sunburnUsername
Page 46 and 47:
CommandRECeiveParameterssrc_spec [d
Page 48 and 49:
eFT: RNT_TIMeout ....... 1200eFT: S
Page 50 and 51:
Executing Local IBM z/OS CommandsUs
Page 52 and 53:
eFT> show local aliaseFT:eFT: BRows
Page 54 and 55:
eFT> local queueJOB SMITHX1T(JOB144
Page 56 and 57:
Page 34 IBM z/OS Local User’s Gui
Page 58 and 59:
Finally, disconnecting from an IBM
Page 60 and 61:
For more information on the REMOTE
Page 62 and 63:
eFT> remote type section.oneeFT:eFT
Page 64 and 65:
Table 1. z/OS File Transfer Qualifi
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
IBM z/OS File or Data Set Specifica
Page 76 and 77:
For example, if a user were to send
Page 78 and 79:
Destination Wildcard Support for IB
Page 80 and 81:
Table 2. Supported z/OS Transfer Mo
Page 82 and 83:
Page 60 File Handling Under IBM z/O
Page 84 and 85:
Second, the exclamation point is us
Page 86 and 87:
within the input level, or input fi
Page 88 and 89:
String LiteralsA string literal as
Page 90 and 91:
Table 3. List of FunctionsFunction
Page 92 and 93:
CHR FunctionThe CHR function return
Page 94 and 95:
DATE FunctionThe DATE function retu
Page 96 and 97:
DFN and NDF FunctionsThe DFN functi
Page 98 and 99:
ENV FunctionThe ENV function return
Page 100 and 101:
EXT FunctionThe EXT function extrac
Page 102 and 103:
LEN FunctionThe LEN function return
Page 104 and 105:
LOWER and UPPER FunctionsThe UPPER
Page 106 and 107:
PARAMS FunctionThe PARAMS function
Page 108 and 109:
STATUS FunctionThe STATUS function
Page 110 and 111:
Disabling String SubstitutionWhen N
Page 112 and 113:
and do not include the special synt
Page 114 and 115: eFT> transferTransfer being made to
Page 116 and 117: Using NetEx/eFT Labels and GOTOsTo
Page 118 and 119: Normally, without ON LOCAL_ERROR or
Page 120 and 121: Host aliases can translate only int
Page 122 and 123: eFT> fetchUser Id? guestPassword? _
Page 124 and 125: Error Message FormattingNetEx/eFT m
Page 126 and 127: * A retry counter limits the number
Page 128 and 129: TRANSLATENote: Do not specify “(S
Page 130 and 131: 2. EXamplesAny examples for the CON
Page 132 and 133: EFTCJCL JOB ,'EFT CLIENT',CLASS=A,M
Page 134 and 135: Tailoring the Standalone Server exe
Page 136 and 137: Page 114 Advanced Local User’s Gu
Page 138 and 139: ASK CommandDescriptionThe ASK comma
Page 140 and 141: CONNECT CommandDescriptionThe CONNE
Page 142 and 143: -PROJect-QUIet-SCRIpt-SEArch-SECond
Page 144 and 145: CONTINUE CommandDescriptionThe CONT
Page 146 and 147: Related TopicsCONNECT CommandSET HO
Page 148 and 149: Related TopicsDISCONNECT CommandQUI
Page 150 and 151: HELP CommandDescriptionThe NetEx/eF
Page 152 and 153: INPUT CommandDescriptionThe INPUT c
Page 154 and 155: The “myalias.ua” script file ca
Page 156 and 157: HOSTOSHOSTTYPENETworkPIDPRODuctSTAT
Page 158 and 159: ON CommandDescriptionThe ON command
Page 160 and 161: Related TopicsGOTO CommandINPUT Com
Page 162 and 163: -QUIet-SPAce-TRUNcate-UNIT-VOLUMEde
Page 166 and 167: ExamplesRefer to “File Handling U
Page 168 and 169: -BLOCKsize-HOST(integer) NETEX nego
Page 170 and 171: SEND CommandDescriptionThe SEND com
Page 172 and 173: SET CommandDescriptionThis form of
Page 174 and 175: SET ALIAS CommandDescriptionThe SET
Page 176 and 177: SET GLOBAL CommandDescriptionThe SE
Page 178 and 179: SET HOST CommandDescriptionThe SET
Page 180 and 181: SET VARIABLE CommandDescriptionThe
Page 182 and 183: SHOW CommandDescriptionSHOW allows
Page 184 and 185: SHOW GLOBAL CommandDescriptionThe S
Page 186 and 187: SHOW QUALIFIER CommandDescriptionSH
Page 188 and 189: TEXT CommandDescriptionCommand TEXT
Page 190 and 191: FormatCommand Qualifier ParameterTR
Page 192 and 193: eFT> translate onPage 170 Command D
Page 194 and 195: Page 172 Host Independent Commands
Page 196 and 197: ASsign Alias CommandDescriptionAssi
Page 198 and 199: DEBUGON Alias Command & DBGON scrip
Page 200 and 201: EDit Alias CommandDescriptionEdit a
Page 202 and 203: LEDit Alias CommandDescriptionInvok
Page 204 and 205: RDir Alias CommandDescriptionShorth
Page 206 and 207: SET LOgin Alias CommandDescriptionA
Page 208 and 209: SHow LOgin Alias CommandDescription
Page 210 and 211: SRD Alias CommandDescriptionA short
Page 212 and 213: TSO Alias CommandDescriptionThe TSO
Page 214 and 215:
ACCOUNT Alias CommandDescriptionThe
Page 216 and 217:
ASCII Alias CommandDescriptionThe A
Page 218 and 219:
BYE Alias CommandDescriptionThe BYE
Page 220 and 221:
CLOSE Alias CommandDescriptionThe C
Page 222 and 223:
DIR Alias CommandDescriptionThe DIR
Page 224 and 225:
GET Alias CommandDescriptionThe GET
Page 226 and 227:
LS Alias CommandDescriptionThe LS a
Page 228 and 229:
MKDIR Alias CommandDescriptionThe M
Page 230 and 231:
PUT Alias CommandDescriptionThe PUT
Page 232 and 233:
RENAME Alias CommandDescriptionThe
Page 234 and 235:
RMDIR Alias CommandDescriptionThe R
Page 236 and 237:
ExampleEncrypting passwords stored
Page 238 and 239:
Table 5. Error MessagesFac Code Sev
Page 240 and 241:
Fac Code Sev Comment TextTable 5. E
Page 242 and 243:
Page 244 and 245:
Fac Code Sev Comment TextTable 5. E
Page 246 and 247:
Page 248 and 249:
UA-501 Protocol error - expected [C
Page 250 and 251:
UA-4501 Nested (or recursive) input
Page 252 and 253:
EFT213-2004 Sequence number error a
Page 254 and 255:
EFT213-8324 Data set exists and -CR
Page 256 and 257:
EFT213-8347 Record length (NNN) exc
Page 258 and 259:
EFT213-8368 Unmatched apostrophes i
Page 260 and 261:
EFT213-9003 Wildcard processing err
Page 262 and 263:
MUX213-8003 Could not find PROCESS:
Page 264 and 265:
DIRECTORY definition ..............
Page 266:
REFER qualifier ...................
show all

NetEx EFT213 Reference Manual Rel 5.4

Create successful ePaper yourself

Delete template?

Save as template?