ISDN Protocol Administrator's and Developer's Guide ... - Intervoice

More documents

Recommendations

Info

ISDN_QSIG_SINGLE_STEP_XFERThe ISDN_QSIG_SINGLE_STEP_XFER subroutine sends a Facilitymessage to the switch to perform a single step transfer.A sample UserSubroutineCall form that callsISDN_QSIG_SINGLE_STEP_XFER is shown below:Parameters:See Table 5-6.Table 5-6. ISDN_QSIG_SINGLE_STEP_XFER ParametersName Required? Type DescriptionTransferNumberYes String Telephone number to which the call is transferredMode Yes Integer The type of call transfer:• 1 – Number is in the Ringing or Alerting states• 2 – Number is in the Answered stateTime Out Yes Integer The maximum time to wait for a switch to complete a transfer orsend an error back that it cannot complete the transfer.* The default is 30 seconds.ANI Optional String The optional ANI for a single-step transfer.5-18 ISDN Protocol Administrator’s and Developer’s Guide 60001262, First Edition
Defining the SubroutinesIn a single-step transfer, the application calls the toolkit functionISDN_QSIG_SINGLE_STEP_XFER with the required parameters, and theswitch completes the transfer immediately. Then it releases the inboundline to the Omvia Media Server.Transfer Error Return Values:A normal single-step transfer does not return any results to theapplication. If the switch rejects a transfer attempt, or if an invalidparameter is passed to the function, an error code is returned to theapplication. If an error occurs, the application programmer must repairthe problem in the InVision application.The error return values for a single-step transfer are shown in Table 5-7below. Error Codes 117 through 123 are switch errors.Table 5-7. Single Step Transfer Error Return ValuesValueDescriptionRange(If Applicable)-100 Toolkit (Mode parameter out of range) (< 1 or > 2)-101 Toolkit (Transfer number too long or too short) (< 1 or > 24)-102 Toolkit (Optional ANI is too long) (> 24)-103 Toolkit (Time value passed is not in range) (< 5 or > 60)-104 Send Post Card Command Timed Out-105 Send Post Card Command received a Post Card not for the TelephonyServices Gateway-106 Send Post Card Command Clear Post Cards Failed-107 Send Post Card Received Bad Cross Reference Value-108 Command Post Card Return Had Bad Mode Parameter (< 1 or > 2)-109 Command Post Card Return Had Bad Transfer Number (< 1 or > 24)-110 Command Post Card Return Had Bad Optional ANI (> 24)-111 Command Post Card Return Had Bad Timeout Value (< 5 or > 60)-112 Query Post Card Timeout-113 Query Post Card Received a Post Card not for the Telephony ServicesGateway-114 Query Post Card Clear Post Cards Failed-115 Query Post Card Received Bad Cross Reference Value-116 Query Post Card Timeout Waiting on Transfer to Complete60001262, First Edition QSIG Protocol 5-19
Page 1:
ISDN Protocol Administrator’s and
Page 4 and 5:
Copyright 2003 Intervoice, Inc.ãAl
Page 7 and 8:
Table of ContentsList of FiguresixL
Page 9 and 10:
Common Subroutines for the ISDN Too
Page 11 and 12:
Call Transfer .....................
Page 13 and 14:
Siemens Cornet N ISDN Protocol 13-1
Page 15:
List of FiguresFigure 2-1. Single-O
Page 18 and 19:
Table 4-15. GET_CONNECTED_PRESENTAT
Page 20 and 21:
Table 6-36. ISDN_DPNS_ACTIVATE_MWI
Page 23 and 24:
About This DocumentPurpose and Audi
Page 25 and 26:
Chapter 10—VN4 ISDN ProtocolDiscu
Page 27 and 28:
Web SiteEntire Documentation SetInt
Page 29 and 30:
InVisionGetting Started with InVisi
Page 31 and 32:
AT&TThe AT&T specifications TR 5007
Page 33 and 34:
British TelecomBritish Telecom spec
Page 35 and 36:
ECMAEuropean Computer Manufacturers
Page 37 and 38:
ConventionsThis document uses the f
Page 39 and 40:
1In this chapter...▼ ISDN Overvie
Page 41 and 42:
ISDN OverviewISDN Reference PointsR
Page 43 and 44:
2In this chapter...▼ Information
Page 45 and 46:
Information ElementsVariable-Length
Page 47 and 48:
Information ElementsTable 2-2. Vari
Page 49 and 50:
ISDN Message TypesCall InformationC
Page 51 and 52:
ISDN Message TypesMiscellaneousMisc
Page 53 and 54:
3In this chapter...▼ T1 Transfer
Page 55 and 56:
T1 Transfer MethodsRelease Link Tru
Page 57 and 58:
E1 Transfer MethodsE1 Transfer Meth
Page 59 and 60:
E1 Transfer MethodsDPNSS 1 Call Tra
Page 61 and 62:
E1 Transfer MethodsQSIG Path-Replac
Page 63 and 64:
4In this chapter...▼ InVision Too
Page 65 and 66:
InVision Toolkits OverviewEach tool
Page 67 and 68:
Using the ISDNTKIT Toolkit Subrouti
Page 69 and 70:
Using the ISDNTKIT Toolkit Subrouti
Page 71 and 72:
Defining the ISDNTKIT Toolkit Subro
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81:
Page 84 and 85:
Return Values:See Table 4-10.Table
Page 86 and 87:
GET_CONNECTED_NUMBER_ALLUse the GET
Page 88 and 89:
GET_CONNECTED_NUMBERING_PLANUse the
Page 90 and 91:
GET_CONNECTED_PRESENTATION_INDICATO
Page 92 and 93:
GET_CONNECTED_SCREENING_INDICATORUs
Page 94 and 95:
GET_CONNECTED_TYPE_OF_NUMBERUse the
Page 96 and 97:
GET_DISCONNECT_CAUSE_CODEThe last r
Page 98 and 99:
Table 4-19. GET_DISCONNECT_CAUSE_CO
Page 100 and 101:
GET_DNIS_ALLUse the GET_DNIS_ALL su
Page 102 and 103:
GET_DNIS_NUMBERING_PLANUse the GET_
Page 104 and 105:
GET_DNIS_TYPE_OF_NUMBERUse the GET_
Page 106 and 107:
GET_ORIGINAL_CALLED_NUMBERUse the G
Page 108 and 109:
GET_ORIGINAL_CALLED_NUMBER_ALLUse t
Page 110 and 111:
Table 4-27. GET_ORIGINAL_CALLED_NUM
Page 112 and 113:
Table 4-28 displays the numbering p
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121: Return Values:See Table 4-32.Table
Page 126 and 127: GET_REDIRECTION_NUMBERING_PLANUse t
Page 128 and 129: GET_REDIRECTION_PRESENTATION_INDICA
Page 130 and 131: GET_REDIRECTION_REASONUse the GET_R
Page 132 and 133: GET_REDIRECTION_SCREENING_INDICATOR
Page 134 and 135: GET_REDIRECTION_TYPE_OF_NUMBERUse t
Page 136 and 137: GET_UUIUse the GET_UUI subroutine t
Page 138 and 139: SET_AND_SEND_CONNECTED_NUMBER_ELEME
Page 140 and 141: Table 4-42. SET_AND_SEND_CONNECTED_
Page 142 and 143: SET_AND_SEND_ORIGINAL_CALLED_NUMBER
Page 144 and 145: Table 4-44. SET_AND_SEND_ORIGINAL_C
Page 146 and 147: SET_AND_SEND_REDIRECTION_NUMBER_ELE
Page 148 and 149: Table 4-46. SET_AND_SEND_REDIRECTIO
Page 150 and 151: SET_AND_SEND_UUI_ELEMENTUse the SET
Page 154 and 155: QSIG OverviewFor more information o
Page 156 and 157: Figure 5-2 displays the first part
Page 158 and 159: QSIG ConfigurationTable 5-1 lists t
Page 160 and 161: [EncodingType]; Optional Parameter:
Page 162 and 163: [EncodingType]Determines the coding
Page 164 and 165: QSIG Path Replace TransferThe Path
Page 166 and 167: ISDN_QSIG_HOLDUse the ISDN_QSIG_HOL
Page 168 and 169: ISDN_QSIG_STARTXFERThe ISDN_QSIG_ST
Page 172 and 173: Table 5-7. Single Step Transfer Err
Page 174 and 175: DPNSS 1 OverviewDPNSS 1 is primaril
Page 176 and 177: Table 6-1. DPNSS 1 Network Layer Me
Page 178 and 179: Extension Status (BTNR 188 Section
Page 180 and 181: DPNSS 1 Network StructureDPNSS 1 re
Page 182 and 183: Table 6-3 displays the Supplementar
Page 184 and 185: Table 6-3. Supplementary Informatio
Page 186 and 187: DPNSS 1 ConfigurationTable 6-4 list
Page 188 and 189: 0 ; Gain adjustment 2 -12..0..41 1
Page 190 and 191: Optional EntriesOptional configurat
Page 192 and 193: Table 6-5. Alphabetical List of DPN
Page 194 and 195: ISDN_DPNS_GET_ANIUse the ISDN_DPNS_
Page 196 and 197: Return Values:See Table 6-8.Table 6
Page 198 and 199: ISDN_DPNS_GET_DNISUse the ISDN_DPNS
Page 202 and 203: ISDN_DPNS_AUTO_OPT_ENQUse the ISDN_
Page 206 and 207: A sample UserSubroutineCall form th
Page 208 and 209: Sample MessagesTwo EEMC and possibl
Page 212 and 213: Parameters:See Table 6-17.Table 6-1
Page 214 and 215: ISDN_DPNS_GET_DIVERSION_INFOUse the
Page 216 and 217: ISDN_DPNS_ACTIVATE_CONTROLLED_DIVER
Page 218 and 219: ISDN_DPNS_DEACTIVATE_CONTROLLED_DIV
Page 220 and 221:
ISDN_DPNS_GET_CONTROLLED_DIVERSIONU
Page 222 and 223:
Call TransferCall transfer is the p
Page 224 and 225:
Page 226 and 227:
Parameters:See Table 6-26.Table 6-2
Page 228 and 229:
Executive IntrusionExecutive intrus
Page 230 and 231:
Page 232 and 233:
Sample MessagesSome typical ISRMC m
Page 234 and 235:
ISDN_DPNS_GET_L3STATE_TXTUse the IS
Page 236 and 237:
ISDN_DPNS_GET_L3_STATEUse the ISDN_
Page 238 and 239:
Message Waiting IndicatorA Message
Page 240 and 241:
Parameters:See Table 6-36.Table 6-3
Page 242 and 243:
Page 244 and 245:
ISDN_DPNS_GET_ASCII_MESSAGEUse the
Page 246 and 247:
Service Indicator CodeThe Service I
Page 248 and 249:
Page 250 and 251:
Calling/Called Line Category (CLC)T
Page 252 and 253:
ISDN_DPNS_SET_CLCUse the ISDN_DPNS_
Page 255 and 256:
7In this chapter...▼ EU4 Overview
Page 257 and 258:
Euro-ISDN ConfigurationDefining int
Page 259 and 260:
Euro-ISDN ConfigurationOptional Ent
Page 261 and 262:
Defining the EU4 SubroutinesParamet
Page 263 and 264:
Defining the EU4 SubroutinesTable 7
Page 265 and 266:
Defining the EU4 SubroutinesReturn
Page 267 and 268:
Page 269:
Page 272 and 273:
AT&T OverviewThe AT&T Custom ISDN w
Page 274 and 275:
Required EntriesThe required entrie
Page 276 and 277:
Required EntriesThe intvconf.dat en
Page 278 and 279:
Optional EntriesThe optional entrie
Page 280 and 281:
Parameters:See Table 8-2.Table 8-2.
Page 282 and 283:
Return Values:See Table 8-5.Table 8
Page 284 and 285:
Hicom OverviewThe Hicom ISDN protoc
Page 286 and 287:
Required EntriesThe required entrie
Page 289 and 290:
10In this chapter...▼ VN4 Overvie
Page 291 and 292:
VN4 ConfigurationDefining intvconf.
Page 293 and 294:
Defining the VN4 SubroutinesVN4_TRA
Page 295 and 296:
Defining the VN4 SubroutinesCertain
Page 297 and 298:
Defining the VN4 SubroutinesTable 1
Page 299 and 300:
11In this chapter...▼ Nortel DMSO
Page 301 and 302:
Nortel DMS ConfigurationDefining in
Page 303 and 304:
Nortel DMS ConfigurationOptional En
Page 305 and 306:
Defining the DMS SubroutinesA sampl
Page 307 and 308:
Defining the DMS SubroutinesISDN_DM
Page 309 and 310:
Defining the DMS SubroutinesGET_RLT
Page 311 and 312:
Defining the DMS SubroutinesGET_RLT
Page 313 and 314:
12In this chapter...▼ National IS
Page 315 and 316:
National ISDN-2 ConfigurationDefini
Page 317 and 318:
National ISDN-2 ConfigurationOption
Page 319 and 320:
Defining the National ISDN-2 Subrou
Page 321 and 322:
13In this chapter...▼ Siemens Cor
Page 323 and 324:
Siemens Cornet N ISDN Configuration
Page 325 and 326:
Siemens Cornet N ISDN Configuration
Page 327 and 328:
14In this chapter...▼ ISDN Consol
Page 329 and 330:
Using ISDN ConsoleUsing ISDN Consol
Page 331 and 332:
Using ISDN ConsoleSystem Configurat
Page 333 and 334:
Using ISDN ConsoleN200 (retransmiss
Page 335 and 336:
Using ISDN ConsoleT316Starts follow
Page 337 and 338:
Using ISDN ConsoleCall Reference Nu
Page 339 and 340:
Using ISDN ConsoleLink Level Statis
Page 341 and 342:
Using ISDN ConsoleAbortsIndicates t
Page 343 and 344:
Using ISDN ConsoleReleaseIndicates
Page 345 and 346:
Using ISDN ConsoleI/O LogThe I/O Lo
Page 347 and 348:
Using ISDN ConsoleThe B Channel Tra
Page 349 and 350:
Using ISDN ConsoleB Channel AccessT
Page 351 and 352:
Using ISDN ConsoleLevel 3 StateIndi
Page 353 and 354:
Using ISDN ConsoleTimers Supported
Page 355 and 356:
Establishing Synchronization with H
Page 357 and 358:
Establishing Synchronization with H
Page 359 and 360:
Enabling Logging for ISDNLayer 2 Li
Page 361 and 362:
Running ISDN Back to Back Between O
Page 363 and 364:
Establishing Layer Three LinkTable
Page 365 and 366:
Establishing Layer Three LinkIdenti
Page 367 and 368:
Establishing Layer Three LinkISDN M
Page 369:
Establishing Layer Three LinkTable
Page 372 and 373:
Standard ConfigurationDigitalT1 Con
Page 375 and 376:
BIn this appendix...▼ Country-Spe
Page 377:
Country-Specific EntriesTable B-1.
Page 380 and 381:
MAINLogCustomer Application FlowPre
Page 382 and 383:
LogFile: appl.logFormat: DatabaseLo
Page 384 and 385:
LogLogcallStatusFile: appl.logForma
Page 386 and 387:
ISDN_QSIG_STARTXFLogFile: appl.logF
Page 388 and 389:
LogFile: appl.logFormat: DatabaseLo
Page 390 and 391:
MAIN July 25, 2003 Final2B
Page 392 and 393:
MAIN July 25, 2003 Final2D
Page 394 and 395:
SWERINGn Codering)BusyGiveUpInformC
Page 396 and 397:
MAIN July 25, 2003 Final2H
Page 398 and 399:
MAIN July 25, 2003 Final3A
Page 400 and 401:
MAIN July 25, 2003 Final3C
Page 402 and 403:
Code ==>> ',(returnCodeasString)Pos
Page 404 and 405:
MAIN July 25, 2003 Final3G
Page 406 and 407:
MAIN July 25, 2003 Final3I
Page 408 and 409:
ISDN_QSIG_SINGLE_STEP_XFER_Call: IS
Page 410 and 411:
MAIN July 25, 2003 Final4D
Page 412 and 413:
urn Codering)YReturneMAIN July 25,
Page 414 and 415:
MAIN July 25, 2003 Final4H
Page 416 and 417:
HangErrorDuration: 60 secondsCUser
Page 418 and 419:
MAIN July 25, 2003 Final5C
Page 420 and 421:
MAIN July 25, 2003 Final5E
Page 422 and 423:
MAIN July 25, 2003 Final5G
Page 424 and 425:
MAIN July 25, 2003 Final5I
Page 426 and 427:
American National Standards Institu
Page 428 and 429:
DLL (Dynamic Link Library)A program
Page 430 and 431:
Hz (hertz)A unit of frequency that
Page 432 and 433:
PBX (Private Branch Exchange)A priv
Page 434 and 435:
timeoutThe event that occurs if, af
Page 437 and 438:
Index[DelayVCDRelayInit] 6-18[DPNSS
Page 439 and 440:
DPNSS 1 (Digital Private Network Si
Page 441 and 442:
GET_ORIGINAL_CALLED_TYPE_OF_NUMBER
Page 443 and 444:
Layer 3 Statistics Level 14-16Link
Page 445 and 446:
ISDN_DPNS_GET_CONTROLLED_DIVERSION
Page 447 and 448:
RR Reference Point 1-3R2, defined G
Page 449 and 450:
VN4_GET_CONNECT_INIT_STATE10-4VN4_G
show all

ISDN Protocol Administrator's and Developer's Guide ... - Intervoice

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?