Clamping Tools - EN / Hahn+Kolb

Conventional workpiece clampingMechanical clamping elementsMetal-cutting toolsContinued next pageSlide guidewaysopen type, with transverse roller, used for: measuring technology, testing equipment and gluing unitsApplication: a large travel is possible with a relatively short slide length with corresponding load carrying capacity. Travel is limited by 2 screws in the upperpart and 1 screw in the lower part. These slides only support a small degree of force in the direction of movement. Additional limit stops are required to limit thetravel for greater force.Advantages:•for precise, easy movements and good positioning and reproducibility quality (no stick-slip effect)•guide rails hardened and ground•horizontal application (vertical also available on request)•parallelism tolerance of supporting to clamping surface, depending on slide length 0.012 mm for 100 mmlength to 0.032 mm for 600 mm length•movement tolerance, depending on slide length 0,003 mm for 50 mm travel to 0,014 mm for 500 mmtravel•0.02 mm graduation•spindle pitch error ± 0.02 mm/300 mm•low maintenanceSpecial accessories: locking device, Z axis assembly angle for carriages, sealing for end inserts (strippers,bellows), longitudinal T-slots (structure height increases), no-play precision ball revolving spindle, hydraulicor pneumatic piston drive or NC motor. Prices on request.Slide length mm 25 45 65 55 80 105 205 110 260Slide width mm 30 30 40 60 60 60 60 100 100Overall height mm 17 17 21 28 28 28 28 45 45Travel mm 12 25 40 30 45 60 130 60 165Water pump pliers N 200 360 600 700 1000 1400 2700 2000 520025701 Ident. No. 005 010 030 055 060 065 085 090 105Unit price E (O. R.) (O. R.) (O. R.) (O. R.) (O. R.) (O. R.) (O. R.) (O. R.) (O. R.)* Applies to force occurring at right angles to the direction of movement but only in the area of supporting surfaces or rolls.h Carriages with other dimensions on request.Prod. Gr. 276Continued next pageSlide guidewayswith dovetail, used for: lathe attachments, feeder units and welding systemsNo. 25706 adjustable via threaded spindle, cross crank with scaleNo. 25707 adjustable via threaded spindle, knurled nut with scaleAdvantages:•for great stress or sudden force•vibration reducing•insensitive to dirt deposits during machining•guide finely milled•used horizontally and vertically•parallelism tolerance of supporting to clamping surface, depending on slide length 0.015 mm for 100 mmlength to 0.05 mm for 600 mm length•movement tolerance, depending on slide length 0.005 mm for 50 mm travel to 0.025 mm for 500 mmtravel•0.02 mm graduation•spindle pitch error ± 0.02 mm/300 mmSlide length mm 76 152 203 305Slide width mm 50 50 75 100 100 150 100 150Overall height mm 25 25 32 37 37 50 37 50Travel mm 22 50 50 25 50 50 75 100Water pump pliers kN 0,51 1,02 1,4 1,99 2,41 3,16 3,61 4,22Spindle thread M 6x1 M 6x1 M 8x1 M12x1 M12x1 M20x1 M12x1 M20x1Ident. No. 010 030 060 070 080 110 100 120Overall length mm – – 243 – 294 334 396 43625706 Unit price E – – (O. R.) – (O. R.) (O. R.) (O. R.) (O. R.)Overall length mm 138 214 220 222 273 – – –25707 Unit price E (O. R.) (O. R.) (O. R.) (O. R.) (O. R.) – – –* Applies to force occurring at right angles to the direction of movement but only in the area of supporting surfaces or rolls.h Slide guide with transverse roller guide for longitudinal and transverse movement, with other dimensions and without spindle on request.No. 25706No. 25707Prod. Gr. 276Continued next pageClamps DIN 6314Execution: hardened and tempered steel, DIN 6314, lacquered.Slot width mm 6,6 9 11 14 18 22 26 33Length mm 50 60 80 100 125 125 160 160 200 200 250 250Width mm 20 25 30 40 40 50 50 60 60 70 70 80Height mm 10 12 15 20 20 25 25 30 30 30 35 40For screws M 6 M 8 M 10 M 12 and M 14 M 12 and M 14 M 16 and M 18 M 16 and M 18 M 20 and M 22 M 20 and M 22 M 24 M 24 M 3026120 Ident. No. 010 020 030 040 050 060 070 080 090 100 110 120Unit price E O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R.h Other sizes on request. Prod. Gr. 260594 2011/12