Clamping Tools - EN / Hahn+Kolb

Workpiece clamping5-axis machine vicesContinued next page3-axis and 5-axis basic clamping set and complete set (raw-part clamping)for 3 or 5-axis machining of clamped workpieceExecution:•high clamping force (up to 42 kN) where required – by installation of the bar lathe immediately below thework piece support!•no opening of the clamping chucks under load, no clamping of the machine table•allows max. cutting forces thank to extreme rigidity•the low clamping depth of 8 mm allows a machining from 3 or 5 sides without disturbing edge•any clamping widths, limited only by the size of the machine table, achieved by just shifting both dies•clamps raw parts, machined parts, round and irregularly shaped parts•form-fit clamping without pre-stamping•a 3 or 5 AX 100 can be built onto T-slot plates and tables, on hole grid plates and own equipmentBasic set (without base plate and without supporting strap pairs) and complete set (with pair ofuniversal base plates and supporting strap pairs) are composed of:Mobile and fixed clamping jaw, extension shaft with union nut 60 and 120 mm, threaded spindle, spindlenut, clamping jaws pair with 12 clamping pins, clamping heights above machine table, optional, dependingon the selection of the support rails and adapter plate pairs 100, 125, 150 mm for 3-axes spanner and 175,200, 250 mm for 5-axes spanner.1 2Metal-cutting tools3100125150175200225250Clamping heights in mmProduct video:use your mobile phone to scan theQR code.Version 3 AX 100 5 AX 100Jaw width mm 100 100Clamping width with standard set mm 22-236 22-236Height above machine table mm 100 175Clamping force on work piece kN 22 42Clamping depth mm 8 828758 Basic set Ident. No. 005 010Unit price E O. R. O. R.28758 Complete set Ident. No. 015d 020dUnit price E O. R. O. R.456 71 3-axes clamp basic set2 5-axes clamp basic set3-8 Required accessories for the correspondingapplication:4 Adapter plates raising25/50 mm Ident. No. 170-1755 Supporting strap pairs:6 100/125/150 mmfor 3 AX 100 Ident. No. 390-3947 175/200/225/250 mmfor 5 AX 100 Ident. No. 400-407h Required alignment and fixing set see No. 28758 224 or 228 on page 631.i Selection overview vices page 617.Prod. Gr. 280Continued next pagePair of base plate and T-slot platefor 3-axis and 5-axis clamp1 24 51 without boring 2 for T-slot tables (universal) 4 screw set 5 for hole grid plates T-slot plateDesignation T-slot plate without boring for T-slot tables 5 base plates for hole grid Alignment and fixing 4Set-screwsUniversalplatessetDistance between grooves mm 63 – 63-126 – – – – – – –Hole grid distance mm – – – 40 50 50 – – – –Fastening thread M – – – M 12 M 12 M 16 – – M 12 M 16Slot width mm 14 – – – – – 14 18 – –Overall length/thread length mm – – – – – – – – 67/33 72/30Length/width/height mm 400/160/50 – – – – – – – – –28758 Ident. No. 090 100 111 142 152 156 224 228 712 716Unit price E O. R. – – – – – O. R. O. R. O. R. O. R.Price/pair E – O. R. O. R. O. R. O. R. O. R. – – – –* divided T-slot plate on requesti Selection overview vices page 617.Prod. Gr. 2802011/12631