Clamping Tools - EN / Hahn+Kolb

Conventional workpiece clampingMechanical clamping elementsContinued next pageDeep clamping jaws, model 'Bulle'Execution: hardened, tempered, annealed in burnished finishApplication: the jaws are released with the key for clamping and pushed apart. The clamp is applied to thetool and clamped firmly with the T-slot screws on the supporting plate. Pulling on the lateral screw initiatesthe wedge effect forwards and down, so that the work piece is held firmly. No projecting tensioning screws.Clamps to the slot at any angle. – Deep clamping jaws are supplied with retaining screws, T-nuts and hexagonscrewdriver DIN ISO 2936. – Also available for slot width 20, 24 and 30 mm. Prices on request.Box qty.: Delivered only in sets, set = 2 piecesFor T-slot width mm 12 14 16 18 22 28L x W x H mm 80 x 40 x 20 80 x 40 x 20 100 x 50 x 25 100 x 50 x 25 140 x 78 x 30 140 x 78 x 30Screws mm M 10 M 12 M 14 M 16 M 20 M 24Clamping force F 1/F 2 kN 16/0,6 22/0,9 32/1,2 36/1,4 36/1,4 40/1,6Dimension l1/l2 mm 39/26 39/26 46/34 46/34 65/50 65/5026140 Ident. No. 020 030 040 050 060 070Set price E O. R. O. R. O. R. O. R. O. R. (O. R.)Metal-cutting toolsProd. Gr. 260Continued next pageFlat clamps, model 'Mini-Bulle'Execution: hardened, tempered, annealed in burnished finish, for flat work piecesApplication: due to the wedging effect of the clamping jaws, the work piece is pressed securely onto themachine bed. The horizontal force is absorbed by a screw fitting the size of the slot which provides for perfectclamping without damaging the table.Delivery: with retaining screw and socket head wrench.Box qty.: Delivered only in sets, set = 2 piecesFor T-slot width a mm 12 14 16 18 22Workpiece thickness 'h'* min./max. mm 2,5/13,5 1,5/13,5 2,5/17,0 1,5/16,0 4,5/21,5Height 'X'/h1 mm 5/7 5/8 6/9 6/10 9/14Length l max x b mm 52x18 55x22 68x25 71x28 89x35Clamping force F 1/F 2 kN 5/0,6 5,5/0,7 8/0,9 9/1 16/1,926141 Ident. No. 010 020 030 040 050Set price E O. R. O. R. O. R. O. R. (O. R.)* With max. T-slot depth to DIN 650. To obtain lower clamping heights with minimum groove depth theclamped item can be ground by 'X' mm.Prod. Gr. 260Continued next pageStepped frames DIN 6318Execution: machine casting, lacquered, floor space and step surface milled, with clamping steps each7.5 mm difference in height.Application: for bracketsOverall height mm 50 95 140 185 230Lowest step mm 12,5 57,5 102,5 147,5 192,5Overall width mm 42,5 95 100 105 11026145 Ident. No. 010 020 030 040 050Unit price E O. R. O. R. O. R. (O. R.) O. R.Prod. Gr. 260Continued next pagePacking blocksExecution: made of hardened and tempered steel, lacquered.No. 26150 Packing blockNo. 26151 Packing block set: 8 pieces, size 1, 8 pieces, size 2, 4 pieces, size 3, in sturdy wooden case,support height 22-208 mmSize 1 2 3External dimensions a x b x c mm 33 x 19 x 30 66 x 35,5 x 30 131 x 68 x 30Minimum bearing surface h mm 23 39 71Largest bearing surface H mm 51 107 20826150 Ident. No. 110 120 130Unit price E O. R. O. R. O. R.26151 Packing blocks-set Ident. No. 010Set price E O. R.h Packing blocks can be combined with clampspage 596. Prod. Gr. 2602011/12599