Clamping Tools - EN / Hahn+Kolb

Conventional workpiece clampingMechanical clamping elementsMetal-cutting toolsContinued next pageT-nuts 'Rhombus'Execution: temperedApplication: use from above, then turn, paying attention to the limit stop in the groove. The rhombus T-nuts have the advantage in that they can be insertedfrom above. They are particularly useful with long T-slots or when the holding of the supporting plate does not allow the retaining screws or T-nuts to be introducedfrom the side. The reduced contact surface in the T-slot allows less bearing capacity compared with comparable sizes DIN 508.Minimum order qty.: Ident. No. 010-070 = 5 piecesNominal dimensions of groove mm 12 14 16 18 20 22 28Width A mm 11,7 13,7 15,7 17,7 19,7 21,7 27,7 27,7Thread d M 10 12 14 16 16 20 20 24Length E mm 18 22 25 28 32 35 44 44Height h mm 14 16 18 20 24 28 36 36Height k mm 7 8 9 10 12 14 18 18Tensile strength class 8 8 6 6 8 6 8 626194 Ident. No. 010 020 030 040 050 070 075 080Unit price E O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R.h Aluminium version on request. Prod. Gr. 260Continued next pageT-nutsIdent. No. 010-130 tempered, tensile strength class 10, DIN 508Ident. No. 220-310 tempered, tensile strength class 10, long formIdent. No. 720-810 nut blanks, hardened and tempered steel 0.35-0.45 % C, without thread, for self-manufacture of nuts with non-standard thread.aahdkkhIdent. No. 010-130 Ident. No. 220-310 Ident. No. 720-810 Ident. No. 010-030 Ident. No. 720-810Minimum order qty.: Ident. No. 010-110, 220-290 and 720-810 = 10 piecesNominal dimensions of groove mm 6 8 10 12 14 16 18 20 22 24 28 36Width A mm 5,7 7,7 9,7 11,7 13,7 15,7 17,7 19,7 21,7 23,7 27,7 35,6Thread d M 5 6 8 10 12 14 16 18 20 22 24 30Width E mm 10 13 15 18 22 25 28 32 35 40 44 54Height h mm 8 10 12 14 16 18 20 24 28 32 36 44Height k mm 4 6 6 7 8 9 10 12 14 16 18 22Length mm 10 13 15 18 22 25 28 32 35 40 44 5426195 DIN 508 Ident. No. 010 020 030 040 050 060* 070 080* 090 100* 110 130Unit price E O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R.Length mm – 26 30 36 44 50 56 64 70 – 88 –26195 long shape Ident. No. – 220 230 240 250 260 270 280 290 – 310 –Unit price E – O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. – O. R. –26195 nut blanks Ident. No. – 720 730 740 750 760 770 780 790 800 810 –Unit price E – O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. –* not correspond to DIN 508. Prod. Gr. 260eeContinued next pageFixed T-nutsExecution: precision ground to fit, C 15 case hardened, therefore short alignment times.Application: screwed down in pairs into the standardised 20 mm wide alignment groove of thedevices. By changing the nuts, each device can be used on several machines with different slot widths.Slot dimension on machine (b)/on device mm 12/20 14/20 16/20 18/20Height x length mm 10 x 22 10 x 25 10 x 25 10 x 25For screws DIN 912* M 6 x 10 M 6 x 16 M 6 x 16 M 6 x 1626196 Ident. No. 112 114 116 120Unit price E O. R. O. R. O. R. O. R.ScrewJigSliding block* Screws not supplied.h Other sizes and flat T-nuts on request.Prod. Gr. 260Machine benchContinued next pageLoose T-nuts DIN 6323Execution: C 15 case-hardened and groundApplication: the T-nuts, after rough aligning, are pushed in fully laterally.During transport of the device no T-nuts protruding from beneath and themachine bed cannot be damaged.Ident. No. 212 for small machines = jig groove 12 mmIdent. No. 312-322 for small machines = jig grooves 20 mm1 = device, 2 = supporting plateSlot dimension on machine b 1 mm 12 14 16 18 22Slot dimension on device b 2 mm 12 20 20 20 20 20Dimensions h/h 1 mm 28,6/5,5 14/5,5 14/5,5 14/5,5 14/5,5 50,5/7Dimensions l mm 20 32 32 32 32 4026196 Ident. No. 212 312 314 316 318 322Unit price E O. R. O. R. O. R. O. R. O. R. O. R.Prod. Gr. 260602 2011/12