Clamping Tools - EN / Hahn+Kolb

Lathe and rounding machine accessoriesLathe chucksContinued next pageContinued next pageFace plates DIN 55027Application: for holding irregular shaped work pieces.Execution: flat disc body, casting, with one-part reversible jaws.Jaws can only be adjusted individually via threaded spindle. Jaw guides ground.From Ø 310 mm with extra T-slots.h Face plates for holding with camlock fastening DIN 55029 or long taper on request.Power-operated chucksIn 2, 3 or 4 jaws model with outer diameter of 85-800 mm. The force required to clamp the workpiece is produced by hydraulic, pneumatic or electronic operatingelements. The chucks are available with or without bore, with centrifugal force compensation and quick-change jaw system. For use on lathes or as stationaryversion and for use on drilling and milling machines.Complete range for lathesMetal-cutting tools1 hydraulic units2 hollow clamping and full clamping cylinder3 power-operated chuck with and without through-bore,tensioning spindles, holder on end face4 driven tool, gripper chuck,tool holder, thread cut quick-change chuck,drilling and milling tools, short drill chuck5 back rests6 rotating lathe centre, feed cylinder7 sleeves1 2 3 4 5 67h Prices on request.t Technical Hotline +49 (0)711 9813-360Continued next pageJaws, unhardened1/16" x 90°for power-operated chucksExecution: with ground keyway and pointed teeth 1/16" x 90°, made of steel 16 MnCr S 5.Application: soft clamping jaws for clamping on power-operated chucks, for machining and matching to the workpiece to be machined.Suitable for use with clamping chucks from SCHUNK, FORKARDT, KITAGAWA, RÖHM and SMW. Refer to page 577 for a list of the exact types of chucks.Instructions for hardening can be provided if required. For screwing onto plain jaws.For chuck Ømm 130 160 165/175 200 250/315Keyway width N mm 12 17 14 17 21Dimension A mm 10 15 15 25 30Hole distance b/for mm 16/M 8 22/M 12 20/M 10 22/M 12 28/M 16Width b mm 30 40 35 40 50Height h mm 38 60 60 60 80Length L mm 55 70 68 90 120Toothing 1/16 x 90° 1/16 x 90° 1/16 x 90° 1/16 x 90° 1/16 x 90°22670 set = 3 pieces Ident. No. 130 160 165 200 250Set price E O. R. O. R. O. R. O. R. O. R.h Other dimensions, and segment jaws, reversible top jaws, clamping jaws and special jaws on request. Prod. Gr. 224Continued next pageJaws, unhardened1.5 mm x 60°for power-operated chucksExecution: with ground keyway and pointed teeth 1.5 mm x 60°, made of steel 16 MnCr S 5.Application: soft clamping jaws for clamping on power-operated chucks, for machining and matching to the workpiece to be machined.Suitable for use with clamping chucks from SCHUNK, FORKARDT, KITAGAWA, RÖHM and SMW. Refer to page 577 for a list of the exact types of chucks.Instructions for hardening can be provided if required. For screwing onto plain jaws.For chuckØmm 135 165 210 254 315Keyway width N mm 10 12 14 16 21Dimension A mm 13 15 24 30 39Hole distance b/for mm 14/M 8 20/M 10 25/M 12 30/M 12 30/M 16Width b mm 25 32 35 40 50Height h mm 32 32 40 42 60Length L mm 55 72 95 110 12922671 set = 3 pieces Ident. No. 135 165 210 254 315Set price E O. R. O. R. O. R. O. R. O. R.h Other dimensions, and segment jaws, reversible top jaws, clamping jaws and special jaws on request. Prod. Gr. 2242011/12575