Clamping Tools - EN / Hahn+Kolb

Workpiece clamping5-axis machine vicesContinued next pageJaws and accessories for centre clamping device hemo basicIdent. No. 304 Ident. No. 315 Ident. No. 316 Ident. No. 317 Ident. No. 337 Ident. No. 338Designation Use Dimensions For model For model For model 28780mm ZS 75/100 ZS 75/150 ZS 75/200 Ident. No. Pr./pair E Set pr. E U. pr. ESoft jaw lowcan be individually matched to the workpiece20 x 34,2 x 75 U 301 (O. R.) – –Soft jaw high30 x 34,2 x 75 U 302 (O. R.) – –Hard jaw with flat groovesU 304 (O. R.) – –can be used on 2 sides, rear side is precision-ground20 x 34,2 x 75Hard jaw with pointed grooves U 305 (O. R.) – –Clamping jaws with tread ground for cubic or plate-shaped workpieces 20 x 34,2 x 75 U 306 (O. R.) – –Grip jaws for steel parts clamping forces up to 35 kN 25 x 34,2 x 75 U 307 (O. R.) – –Soft jaw low, narrow20 x 24,6 x 75 U U 310 (O. R.) – –Soft jaw low, wide can be individually matched to the workpiece20 x 49,2 x 75 U U 311 (O. R.) – –Soft jaw high 30 x 49,2 x 75 U U 312 (O. R.) – –Hard jaw with flat grooves, narrow20 x 24,6 x 75 U U 313 (O. R.) – –Hard jaw with flat grooves, wide can be used on 2 sides, rear side is precision-ground20 x 44,5 x 75 U U 314 (O. R.) – –Hard jaw with pointed grooves 20 x 24,6 x 75 U U 315 (O. R.) – –Clamping jaws with tread ground for cubic or plate-shaped workpieces 20 x 49,2 x 75 U U 316 (O. R.) – –Grip jaws for steel parts clamping forces up to 35 kN 25 x 24,6 x 75 U U 317 (O. R.) – –Grip jaws for plastic parts 10x24,6x75 U U 318 (O. R.) – –Clamping screws for grip jawsfor different distancesPendulum jaw adjustment angle ±2°Double pendulum jawincluding 2 replaceable thrust pieces(only for use with pendulum jaw Ident.No. 331)Thrust pieces flat6 pieces U 320 – (O. R.) –10 pieces U U 321 – (O. R.) –16-pieces U U 322 – (O. R.) –30 x 40 x 75 U 330 – – (O. R.)30 x 55 x 75 U U 331 – – (O. R.)guarantees physically correct clamping of 20 x 44,5 x 75 U U 332 – – (O. R.)raw parts or 2 small parts with tolerancesU U 333 (O. R.) – –Thrust pieces with flat grooves used in pairs for Ident. No. 332U U 334 (O. R.) – –Thrust pieces with pointed grooves U U 335 (O. R.) – –Lateral stop bolted U U 336 – – (O. R.)Lateral stop magnetic for unimpeded accessibility U U 337 – – (O. R.)Tool support height to customer request U U 338 (O. R.) – –Metal-cutting toolsi Selection overview vices page 617. Prod. Gr. 285Continued next pageQuick-clamping blocks for hemo basicApplication: manual quick-change system for retooling in seconds.Execution:•draw-in system hardened and ground. Very robust and reliable construction without any external energy•draw-in force: 12 kN•fits parallel or cross-slot T-slot tables and tables with centring pegs•feather key implemented through 90°28780 Quick-clamping block 12 kN Ident. No. 510Unit price E (O. R.)28780 Draw-in bolts Ident. No. 511Unit price E (O. R.)h Further information, advice and quotations available on request.t Technical Hotline +49 (0)711 9813-360i Selection overview vices page 617.Prod. Gr. 285Ident. No. 5102011/12637