Clamping Tools - EN / Hahn+Kolb

Workpiece clampingHigh-pressure machine vicesContinued next pageAccessoriesfor high pressure machine vices No. 28812 and No. 28832Jaw width mm 90 125 160 200Clamping range Ø mm – 15-42 18-50 20-6028833 V-groove jaw, for clamping roundworkpieces horizontally and vertically.Ident. No. – 125 160 200Unit price E – O. R. (O. R.) (O. R.)(depth x height of step) mm – 3 x 6 5 x 8 6 x 1228834 Step jaws, for holding rectangular workpieces Ident. No. – 125 160 200without packing.Set price E – O. R. (O. R.) (O. R.)28835 Pull-down jaws, replacing the standard jaws Ident. No. 092 127 161 –Set price E (O. R.) (O. R.) (O. R.) –28838 V-drive to operate vice spindle from above (supplied Ident. No. – – 160 –with adapter without crank).Unit price E – – (O. R.) –28839 Workpiece stop for precision clamping of workpiecesIdent. No. – – 200Unit price E – – (O. R.)28889 RÖHM workpiece stopper* Ident. No. 010 – –Unit price E O. R. – –No. 28833 125-200No. 28834 125-200No. 28835Metal-cutting toolsi Selection overview vices page 617. No. 28833-28839 = Prod. Gr. 281No. 28889 = Prod. Gr. 203No. 28839 200No. 28838 160Continued next pageHigh pressure machine vicesApplication: for individual and serial production on drilling and milling machines.Execution:•clamping system mechanical-hydraulic with mechanical pretensioning via crank•clamping force can be pre-set via limit stop•steel body, forged (jaw width 113, 135 and 160 mm) spheroidal graphite cast iron (jaw width 200 mm).Guideways hardened and ground•aligned on the machine bed: longitudinal via slots and T-nuts No. 26196. Transverse slot on request atextra cost•rough adjustment of clamping range via rigging pins•consistent precise clamping with clamping force 0.01 mmSupplied with 1 set standard jaws (1 side smooth, 1 side grooved) and crank.yBDmaxJaw width mm 113 135 160 200Clamping width mm 170 220 310 350Jaw height/width C/Y mm 31,6/12 39,6/16 49,6/16 66,6/20Body length F mm 390 468 574 685Overall length D max mm 583 681 817 1022Height G ± 0.02/E mm 65,5/97 72,5/112 83,5/133 104,5/171Width K mm 160 200 240 280Slot width Q mm 13 13 17 21Clamping force kN 30 40 50 10028880 Ident. No. 111 136 161 201Unit price E O. R. O. R. O. R. (O. R.)K EG CM620 H7PFQ20 H7Qh Vices with jaw width 250 and 315 on request.Additional V-drive on request.i Selection overview vices page 617.Prod. Gr. 203Continued next pageJaws, hook-on typeApplication: for high pressure machine vices No. 28880.ENR roller low-tension jaws, for workpieces with/without angle error, hardened and ground.Delivery: Set consists of two hold-on jawsFor jaw width mm 113 135 160 20028882 Ident. No. 110 135 160 200Set price E (O. R.) (O. R.) (O. R.) (O. R.)i Selection overview vices page 617. Prod. Gr. 203No. 28882No. 288822011/12625