Clamping Tools - EN / Hahn+Kolb

Lathe and rounding machine accessoriesLathe chucksMetal-cutting toolsContinued next pageVertical draw-barsApplication: for use on conventional drilling and milling machines and thread cutters, for quick tensioningof work pieces by collets.Clamping range d mm 3-26 3-42Clamping vice width mm 96 135Dimension H mm 80 100Dimension L x L 1 mm 160 x 273 210 x 347Groove size mm 14 1622365 Vertical draw-bar Ident. No. 010 020Unit price E O. R. (O. R.)22366 Collets rising in 1 mm steps Ident. No. 010 020Unit price E (O. R.) (O. R.)h Collet chucks for sq. and hex. on request. Prod. Gr. 250HdLL1Continued next pageColletsPlease state machine type and bore of collet chuck when ordering; also state whether clamping of round, square, hexagon or octagon components is required.If it is not possible to clearly identify the machine type, in addition to the diameter, please give the technical data such as length, diameter of shank and collaretc. as shown in the following drawings.Tension colleth Additional information, advice and quotations available on request.Compression colletContinued next pageMachine spindle headsfor lathe chuck adapters with self-centring taper and flange to DIN 55021For lathe chucks with direct short taper adapter lathe chuck is fastened onto machine spindle with setscrews for shape A, with Allen screws for shape B (fast chuck change).Spindle head size No. of holes on outer F 1 (outer hole No. holes on inner F 2 (inner holeA B C D hole circlecircle) hole circle circle)(F 1) E 1 (F 1) G (F 2) E 23 102 53,985 11 16 3 x M 10 3 x 10,5 75 - -4 112 63,525 11 20 3 x M 10 3 x 10,5 85 - -5 135 82,575 13 22 7 x M 10 4 x 10,5 104,8 8 x M 10 61,96 170 106,390 14 25 7 x M 12 4 x 13 133,4 8 x M 12 82,68 220 139,735 16 28 7 x M 16 4 x 17 171,4 8 x M 16 111,111 290 196,885 18 35 12 x M 20 6 x 21 235 11 x M 20 165,115 380 285,800 20 42 12 x M 24 6 x 25 330,2 11 x M 24 247,6From spindle size 4 with driverForm AForm BContinued next pageMachine spindle headsfor lathe chuck adapters with self-centring taper and flange to DIN 55026For lathe chucks with direct short taper adapter, work is fastened onto the machine spindle from the frontusing Allen screws on the outer or inner hole circleSpindle head size No. of holes on F 1 (outer hole No. holes on F 2 (inner holeA B C 1 C 2 D outer hole circle(F 1) E 1circle) inner hole circle(F 2) E 2circle)3 92 53,983 11 - 16 3 x M 10 70,6 - -4 108 63,521 11 - 20 11 x M 10 82,6 - -5 133 82,573 13 14,288 22 11 x M 10 104,8 8 x M 10 61,96 165 106,385 14 15,875 25 11 x M 12 133,4 8 x M 12 82,68 210 139,731 16 17,462 28 11 x M 16 171,4 8 x M 16 111,111 280 196,883 18 19,05 35 11 x M 20 235 8 x M 20 165,115 380 285,791 19 20,638 42 12 x M 24 330,2 11 x M 24 247,620 520 412,795 21 22,225 48 12 x M 24 463,6 11 x M 24 368,3From taper size 4 with driver564 2011/12