Clamping Tools - EN / Hahn+Kolb

Tool holding fixturesTool holding fixtures DIN 69871 ST 40Continued next pageMilling chucks type ERDesign: case hardened HRC 60-2 (HV 700-50), hardness depth 0.8 mm ± 0.2 mm, burnished.Taper angle tolerance quality 3 according to DIN 2080. Alloyed case-hardened steel with tensile strengthat the core of at least 950 N/mm 2 . With plastic edge protection ring, ring groove.Application: for double-conical collets, type ER No. 23320, slotted on both sides. The tools are held alongthe entire collet chuck length and can also be clamped on the drill heel. The collet chucks are withdrawnfrom the drill chuck through the outlet groove on loosening the clamping nut.Steep taper ST 40Type ER 16 ER 25 ER 32 ER 40Clamping range mm 1-10 2-16 2-20 3-26Clamping nut Ø D mm 32 42 50 63Dimension A mm 50 50 50 8023300 Ident. No. 840 841 842 843Unit price E O. R. O. R. O. R. O. R.DIN 6499 ERSKDMetal-cutting toolsi Tool holding fixtures selection overview page 492. Prod. Gr. 295AContinued next pageMilling chucks type OZ DIN 6391Design: case hardened HRC 60-2 (HV 700-50), hardness depth 0.8 mm ± 0.2 mm, burnished.Taper angle tolerance quality 3 according to DIN 2080. Alloyed case-hardened steel with tensile strengthat the core of at least 950 N/mm 2 . With plastic edge protection ring, ring groove.For collet chucks DIN 6388.milling chuck without collets , with integrated, adjustable length stop screw.Delivery: with clamping nut.Steep taper ST 30 40Clamping range mm 2-16 2-25Dimension Ø D mm 43 60Dimension A* mm 50 6323295 Ident. No. 005 010Unit price E O. R. O. R.h Hook wrench No. 52100 page 532.i Tool holding fixtures selection overview page 492.Prod. Gr. 295SKADContinued next pageFace chucks DIN 6359Design: case hardened HRC 60-2 (HV 700-50), hardness depth 0.8 mm ± 0.2 mm, burnished.Taper angle tolerance quality 3 according to DIN 2080. Alloyed case-hardened steel with tensile strengthat the core of at least 950 N/mm 2 . With plastic edge protection ring, ring groove.Application: for clamping tools with straight shank and clamping area according to DIN 1835 B. They preventthe tool from twisting by maintaining high concentricity.dDSKASteep taper ST 40Tool adapter d 1 mm 6 8 10 12 14 16 20 25 32Dimension Ø D mm 25 28 35 42 44 48 52 65 72Dimension A mm 50 50 50 50 63 63 80 80 8023330 Ident. No. 840 841 842 843 844 845 846 847 848Unit price E O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R. O. R.h Version for DIN 1835 E on request.i Tool holding fixtures selection overview page 492.Prod. Gr. 295Continued next pageDrill chuck holdersExecution: hardened, taper shaft and drill chuck cone ground.Tolerances of taper shanks according to DIN 2080 AT 3.Application: for holding 3-jaw chucks. We recommend the chuck No. 21305 and 21311.Take-up shank, steep taperDIN 69871 ASteep taper ST 40**Drill chuck B 16Dimension A mm 2623272 Ident. No. 510Unit price E O. R.Ah ** See required pull studs No. 23690 page 541.i Tool holding fixtures selection overview page 492.Prod. Gr. 2062011/12495