TOTAL STATION InstructIon manual

More documents

Recommendations

Info

•Factory default setting of SENDING1. BAUD RATE: 96002. DATA LENGTH: 83. PARITY BITS: NIL4. STOP BITS: 15. SIGNAL CONTROL: ON6. XON/XOFF: ON7. PROTOCOL: ON8. RECORD DELIMETER: CR+LF9. DISP.1 AXIS: BASIS DIRECT10. DISP.2 AXIS: RIGHT ANGLE11. DISP.3 AXIS: HEIGHT12. ROTATION: CW[3. SEND POLAR DATA]Select the 3. SEND POLAR DATA and press [ENT]to view the following screen.Press [ENT] to open the selection window. Selecteach setting and press the [ENT].Press [ACCEPT] when all selections are made.•Factory default setting of 3. SEND POLAR DATA1. BAUD RATE: 96002. DATA LENGTH: 83. PARITY BITS: NIL4. STOP BITS: 15. SIGNAL CONTROL: ON6. XON/XOFF: ON7. ROTATION: CW127
13.3.4 About DataLink DL-01 SoftwareDataLink DL-01 Software allows you to send collected data by R-400 to other devices,to receive coordinates data, and to convert the resulting files into a number of commonformats.a) Recommendation for "PN".It is recommended that “PN” (Point Name) data should consist of les or equal to 4(one-byte) numeric characters to convert files with DL-01. Because, it may not beconverted properly if alphabetic characters or more than 5 (one-byte) numericcharacters are used for the “PN”.b) Notes for the data transferring.Please, be careful about following items for the data transfer with "DL-01".b-1 Type of data, which can be transferred.With PTL, “POLAR DATA” can be transfered by “DC1” or “AUX” format.In addition, it is possible DL-01 to receive/convert “POLAR DATA” with “DC1 (DC-1Z) ” format.b-2 Notes for unit.If you are requested to select unit when you convert data on DL-01, please select unitaccording to the settings on R-400.b-3 Limitation for each format.Please, use “CSV” or “DC1( DC-1Z)”format to transfer data to/from R-400.Limitation for the "CSV" format.With the “CSV” format, “PN” and “PC (Point Code)”data that consists of les or equalto 15 (one-byte) characters can be transferred.Limitations for the "DC1 (DC-1Z)" format.With “DC1 (DC-1Z)” format, the length of “PN” data should consist of les or equalto 11 (one-byte) characters. And with the “DC1 (DC-1Z)” format “PC” data cannotbe transferred.128
Page 1 and 2:
Total StationR-400seriesInstruction
Page 3 and 4:
4.8 Offset 324.9 Station setup [By
Page 5 and 6:
Before using this product, be sure
Page 7 and 8:
FUNCTION KEY[ ▽ ] F1 Moves the cu
Page 9 and 10:
1. INTRODUCTION1.1 IntroductionThan
Page 11 and 12:
•IH and PHIH stands for “Instru
Page 13 and 14:
2.2 Allocation of each PowerTopoLit
Page 15 and 16:
3.FILE MANAGERThe Data storage memo
Page 17 and 18:
Input your desired JOB NAME and pre
Page 19 and 20:
4. MEASUREOffset3.Rotated planeRefe
Page 21 and 22:
4.1.2 Coordinates, X, Y, Z, IH, and
Page 23 and 24:
• [OTHER] KeyTo select the job fi
Page 25 and 26:
4.3 Function of MEASURE screenAim a
Page 27 and 28:
3.Rotated planeREMOTEReference P. C
Page 29 and 30:
4.4.3 StationPress [F3][STATION] to
Page 31 and 32:
Input ppm value.Press [ENT].TEMP, P
Page 33 and 34:
EDM settings can be selected by pre
Page 35 and 36:
4.10 Station OrientationPress the [
Page 37 and 38:
Press [F2][OFFSET] to display OFFSE
Page 39 and 40:
5. VIEW AND EDITStored data are dis
Page 41 and 42:
Your desired points are deleted and
Page 43 and 44:
Import ProcedurePress [F3][I/O] on
Page 45 and 46:
6. FREE STATIONING?Point 2 Coordina
Page 47 and 48:
For precise measurement, carry out
Page 49 and 50:
Press the [F1][MEAS] to measure the
Page 51 and 52:
7. STAKE OUTFrom the known Station
Page 53 and 54:
To display all information at once,
Page 55 and 56:
Press the [F4][NEXT] to carry out s
Page 57 and 58:
A -> BDistance between Point A and
Page 59 and 60:
7.3.1 Three pointP1OP3Stake Out Poi
Page 61 and 62:
7.3.2 Circle radiusCPRADIUSStake Ou
Page 63 and 64:
8. CALCULATIONS8.1 CogoThe followin
Page 65 and 66:
•[LIST] keyAll stored points can
Page 67 and 68:
8.1.2 Point CoordinatesBearingDista
Page 69 and 70:
Input your desired PC by pressing k
Page 71 and 72:
Press [ENT] to view the following s
Page 73 and 74:
8.1.4 Line-Arc intersectionPoint 1E
Page 75 and 76:
8.1.5 Line-Line intersectionInterse
Page 77 and 78: 8.1.6 Arc-Arc intersectionCenter 2A
Page 79 and 80: Press [F5][ENT] to save one of inte
Page 81 and 82: Press [F5][ENT] to save the coordin
Page 83 and 84: Press [F5][ENT] to save the coordin
Page 85 and 86: Input DISTANCE (Distance from SP to
Page 87: Select 2. 2D SURFACE and press [ENT
Page 90 and 91: This function calculates the center
Page 92 and 93: From the PowerTopoLite screen, pres
Page 94 and 95: 9. VPM (Virtual Plane Measurement)P
Page 96 and 97: Press [ENT] to view the COORD.ON TH
Page 98 and 99: Aim at the Target 1 and press [F1][
Page 100 and 101: Closed traverseOpen traverseThe fol
Page 102 and 103: Input the TEMP value.Press [ENT].In
Page 104 and 105: Press the [ENT] to view the AIM AT
Page 106 and 107: Press [ENT] to open the Z coordinat
Page 108 and 109: 12. ROAD DESIGNYou can use this fun
Page 110 and 111: 12.1 BP, IP, EP inputPress [F2][ROA
Page 112 and 113: Press [F5] [ACCEPT] after parameter
Page 114 and 115: NOTE: When you want to stop functio
Page 116 and 117: [L/F code] use CR/LFBCC is calculat
Page 118 and 119: Select the file you desire to outpu
Page 120 and 121: • Thenumber of data exceeds the m
Page 122 and 123: 13.1.3.2 Reading data settingSelect
Page 124 and 125: CAUTION•DAT file in the internal
Page 126 and 127: Press [ENT], and set the PC to be r
Page 130 and 131: -4 Recommended communication settin
Page 132 and 133: d) Note on converting CSV file.When
Page 134 and 135: 14.1 Language selectionSelect 1. LA
Page 136 and 137: Any name can be defined for all thr
Page 138 and 139: Process typeThis input method takes
Page 140 and 141: When “LARGE CHARACTOR”is select
Page 142 and 143: Select 9.Elevation factor and press
Page 144: TI Asahi Co., Ltd.International Sal
show all

TOTAL STATION InstructIon manual

Create successful ePaper yourself

Delete template?

Save as template?