TOTAL STATION InstructIon manual

More documents

Recommendations

Info

NOTE: [F1][ORDER] keyPress [F1][ORDER] to confirm order ofselected points after you finished theselection. If you finish point selection of apolygon, press [F1][ACCEPT] tocalculate. The result of calculation isdisplayed as follows.Press [ENT] or [ESC] to return to POINT SELECTION FROM THE LIST screen. Youchange a selection, and you can calculate it again.8.3 3D Surface and Volume2D-CONTOUR Plane Figure Profile Figure2D & 3DSurfaceProfile Figure88
Page 1 and 2:
Total StationR-400seriesInstruction
Page 3 and 4:
4.8 Offset 324.9 Station setup [By
Page 5 and 6:
Before using this product, be sure
Page 7 and 8:
FUNCTION KEY[ ▽ ] F1 Moves the cu
Page 9 and 10:
1. INTRODUCTION1.1 IntroductionThan
Page 11 and 12:
•IH and PHIH stands for “Instru
Page 13 and 14:
2.2 Allocation of each PowerTopoLit
Page 15 and 16:
3.FILE MANAGERThe Data storage memo
Page 17 and 18:
Input your desired JOB NAME and pre
Page 19 and 20:
4. MEASUREOffset3.Rotated planeRefe
Page 21 and 22:
4.1.2 Coordinates, X, Y, Z, IH, and
Page 23 and 24:
• [OTHER] KeyTo select the job fi
Page 25 and 26:
4.3 Function of MEASURE screenAim a
Page 27 and 28:
3.Rotated planeREMOTEReference P. C
Page 29 and 30:
4.4.3 StationPress [F3][STATION] to
Page 31 and 32:
Input ppm value.Press [ENT].TEMP, P
Page 33 and 34:
EDM settings can be selected by pre
Page 35 and 36:
4.10 Station OrientationPress the [
Page 37 and 38: Press [F2][OFFSET] to display OFFSE
Page 39 and 40: 5. VIEW AND EDITStored data are dis
Page 41 and 42: Your desired points are deleted and
Page 43 and 44: Import ProcedurePress [F3][I/O] on
Page 45 and 46: 6. FREE STATIONING?Point 2 Coordina
Page 47 and 48: For precise measurement, carry out
Page 49 and 50: Press the [F1][MEAS] to measure the
Page 51 and 52: 7. STAKE OUTFrom the known Station
Page 53 and 54: To display all information at once,
Page 55 and 56: Press the [F4][NEXT] to carry out s
Page 57 and 58: A -> BDistance between Point A and
Page 59 and 60: 7.3.1 Three pointP1OP3Stake Out Poi
Page 61 and 62: 7.3.2 Circle radiusCPRADIUSStake Ou
Page 63 and 64: 8. CALCULATIONS8.1 CogoThe followin
Page 65 and 66: •[LIST] keyAll stored points can
Page 67 and 68: 8.1.2 Point CoordinatesBearingDista
Page 69 and 70: Input your desired PC by pressing k
Page 71 and 72: Press [ENT] to view the following s
Page 73 and 74: 8.1.4 Line-Arc intersectionPoint 1E
Page 75 and 76: 8.1.5 Line-Line intersectionInterse
Page 77 and 78: 8.1.6 Arc-Arc intersectionCenter 2A
Page 79 and 80: Press [F5][ENT] to save one of inte
Page 81 and 82: Press [F5][ENT] to save the coordin
Page 83 and 84: Press [F5][ENT] to save the coordin
Page 85 and 86: Input DISTANCE (Distance from SP to
Page 87: Select 2. 2D SURFACE and press [ENT
Page 91 and 92: In 3D Volume, the case that input r
Page 93 and 94: 8.4 REM8.4.1 General pictures of me
Page 95 and 96: Press [ENT] to open the input windo
Page 97 and 98: 10. RDM (Remote Distance Measuremen
Page 99 and 100: 11. TRAVERSEFixed traverseEnd point
Page 101 and 102: 11.1 Start point measuringSelect 1.
Page 103 and 104: Aim at the reference point and pres
Page 105 and 106: NOTE:Don’t use the same point nam
Page 107 and 108: FIXED TRAVERSESet the instrument in
Page 109 and 110: [Generation of principal peg to be
Page 111 and 112: In the same manner, input the value
Page 113 and 114: 12.4 CalculationPress [F1] [NO] on
Page 115 and 116: 13. INPUT / OUTPUTThe communication
Page 117 and 118: 13.1 Text File read / writeText fil
Page 119 and 120: Select the file you desire to read,
Page 121 and 122: 13.1.3 Text File setupWhen coordina
Page 123 and 124: 13.2 Communication with USBBy conne
Page 125 and 126: Set the PC to be ready to send and
Page 127 and 128: •Factory default setting of RECEI
Page 129 and 130: 13.3.4 About DataLink DL-01 Softwar
Page 131 and 132: For seting “Type of Device” in
Page 133 and 134: 14. PREFERENCEFollowings are possib
Page 135 and 136: Definition of each selection is as
Page 137 and 138: 2. Full templateSelect each Charact
Page 139 and 140:
1. Cylinder faceAngleCylinderThe Re
Page 141 and 142:
1. PRIM.MAES KEY 1. MEAS. SHOT2. ME
Page 143 and 144:
14.11 Meas. displayThis setting all
show all

TOTAL STATION InstructIon manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?