TOTAL STATION InstructIon manual

More documents

Recommendations

Info

Coordinates display and Angle & Distance display1) Press [F5][PAGE] twice to view [F3][ANG & DIST].2) Press [F3][ANG & DIST] to view [F3][COORD.] and Angle and Distance values.3) Press [F3][COORD.] to view [F3][ANG&DIST] and Coordinates.Stakeout can be selected by pressing [F4][STAKEOUT].4.4 Remote, Offset, Station, and H. angle function4.4.1 RemotePress [F5][PAGE] to view another MEASUREmenu.Press [F1][REMOTE] once and then quickly pressthis key again to measure your desired pointCoordinates by moving the telescope.The displayed Coordinates automatically change according to your aiming point.The Remote is a function of, so to speak,“Real-time ofset”. If a reference point or ofsetpoint is measured, the Coordinates of your aiming point are calculated based on the referenceplane.There are three calculation methods: Cylindrical face, Fixed plane and Rotated plane.They are selected by “14.Preference”. Refer to “14.5Remote method selection”.The calculations are performed on the virtual planes.To quit the Remote measurement, press [F1][REMOTE] twice again.25
3.Rotated planeREMOTEReference P. Coordinates1.Cylinder face2.Fixed planeStation Point Coordinates4.4.2 OffsetPress the [F2][OFFSET] to view the OFFSETSscreen.Offset enables you to work with Offsets.The following offsets are available.Press [ENT] to view the offset input window.Input the RO offset value by pressing keys.VO, DO and TO values are input in the samemanner.After input “TO”value, press [ENT] to view theMEASURE screen.(Or press [ESC] then press [ACCEPT].)The offset values are added to X,Y and Z values.The input value of offset is cleared when you save the surveying point and step forwardto the next surveying point.26
Page 1 and 2: Total StationR-400seriesInstruction
Page 3 and 4: 4.8 Offset 324.9 Station setup [By
Page 5 and 6: Before using this product, be sure
Page 7 and 8: FUNCTION KEY[ ▽ ] F1 Moves the cu
Page 9 and 10: 1. INTRODUCTION1.1 IntroductionThan
Page 11 and 12: •IH and PHIH stands for “Instru
Page 13 and 14: 2.2 Allocation of each PowerTopoLit
Page 15 and 16: 3.FILE MANAGERThe Data storage memo
Page 17 and 18: Input your desired JOB NAME and pre
Page 19 and 20: 4. MEASUREOffset3.Rotated planeRefe
Page 21 and 22: 4.1.2 Coordinates, X, Y, Z, IH, and
Page 23 and 24: • [OTHER] KeyTo select the job fi
Page 25: 4.3 Function of MEASURE screenAim a
Page 29 and 30: 4.4.3 StationPress [F3][STATION] to
Page 31 and 32: Input ppm value.Press [ENT].TEMP, P
Page 33 and 34: EDM settings can be selected by pre
Page 35 and 36: 4.10 Station OrientationPress the [
Page 37 and 38: Press [F2][OFFSET] to display OFFSE
Page 39 and 40: 5. VIEW AND EDITStored data are dis
Page 41 and 42: Your desired points are deleted and
Page 43 and 44: Import ProcedurePress [F3][I/O] on
Page 45 and 46: 6. FREE STATIONING?Point 2 Coordina
Page 47 and 48: For precise measurement, carry out
Page 49 and 50: Press the [F1][MEAS] to measure the
Page 51 and 52: 7. STAKE OUTFrom the known Station
Page 53 and 54: To display all information at once,
Page 55 and 56: Press the [F4][NEXT] to carry out s
Page 57 and 58: A -> BDistance between Point A and
Page 59 and 60: 7.3.1 Three pointP1OP3Stake Out Poi
Page 61 and 62: 7.3.2 Circle radiusCPRADIUSStake Ou
Page 63 and 64: 8. CALCULATIONS8.1 CogoThe followin
Page 65 and 66: •[LIST] keyAll stored points can
Page 67 and 68: 8.1.2 Point CoordinatesBearingDista
Page 69 and 70: Input your desired PC by pressing k
Page 71 and 72: Press [ENT] to view the following s
Page 73 and 74: 8.1.4 Line-Arc intersectionPoint 1E
Page 75 and 76: 8.1.5 Line-Line intersectionInterse
Page 77 and 78:
8.1.6 Arc-Arc intersectionCenter 2A
Page 79 and 80:
Press [F5][ENT] to save one of inte
Page 81 and 82:
Press [F5][ENT] to save the coordin
Page 83 and 84:
Press [F5][ENT] to save the coordin
Page 85 and 86:
Input DISTANCE (Distance from SP to
Page 87:
Select 2. 2D SURFACE and press [ENT
Page 90 and 91:
This function calculates the center
Page 92 and 93:
From the PowerTopoLite screen, pres
Page 94 and 95:
9. VPM (Virtual Plane Measurement)P
Page 96 and 97:
Press [ENT] to view the COORD.ON TH
Page 98 and 99:
Aim at the Target 1 and press [F1][
Page 100 and 101:
Closed traverseOpen traverseThe fol
Page 102 and 103:
Input the TEMP value.Press [ENT].In
Page 104 and 105:
Press the [ENT] to view the AIM AT
Page 106 and 107:
Press [ENT] to open the Z coordinat
Page 108 and 109:
12. ROAD DESIGNYou can use this fun
Page 110 and 111:
12.1 BP, IP, EP inputPress [F2][ROA
Page 112 and 113:
Press [F5] [ACCEPT] after parameter
Page 114 and 115:
NOTE: When you want to stop functio
Page 116 and 117:
[L/F code] use CR/LFBCC is calculat
Page 118 and 119:
Select the file you desire to outpu
Page 120 and 121:
• Thenumber of data exceeds the m
Page 122 and 123:
13.1.3.2 Reading data settingSelect
Page 124 and 125:
CAUTION•DAT file in the internal
Page 126 and 127:
Press [ENT], and set the PC to be r
Page 128 and 129:
•Factory default setting of SENDI
Page 130 and 131:
-4 Recommended communication settin
Page 132 and 133:
d) Note on converting CSV file.When
Page 134 and 135:
14.1 Language selectionSelect 1. LA
Page 136 and 137:
Any name can be defined for all thr
Page 138 and 139:
Process typeThis input method takes
Page 140 and 141:
When “LARGE CHARACTOR”is select
Page 142 and 143:
Select 9.Elevation factor and press
Page 144:
TI Asahi Co., Ltd.International Sal
show all

TOTAL STATION InstructIon manual

Create successful ePaper yourself

Delete template?

Save as template?