Atmel AT89C51ID2 Data Sheet - Keil

More documents

Recommendations

Info

86 AT89C51ID2 its own slave address followed by the data direction bit which must be at logic 1 (R) for TWI to operate in the slave transmitter mode. After its own slave address and the R bit have been received, the serial interrupt flag is set and a valid status code can be read from SSCS. This status code is used to vector to an interrupt service routine. The appropriate action to be taken for each of these status code is detailed in Table . The slave transmitter mode may also be entered if arbitration is lost while the TWI module is in the master mode. If the AA bit is reset during a transfer, the TWI module will transmit the last byte of the transfer and enter state C0h or C8h. the TWI module is switched to the not addressed slave mode and will ignore the master receiver if it continues the transfer. Thus the master receiver receives all 1’s as serial data. While AA is reset, the TWI module does not respond to its own slave address. However, the 2-wire bus is still monitored and address recognition may be resume at any time by setting AA. This means that the AA bit may be used to temporarily isolate the TWI module from the 2-wire bus. Miscellaneous States There are two SSCS codes that do not correspond to a define TWI hardware state (Table 69 ). These codes are discuss hereafter. Status F8h indicates that no relevant information is available because the serial interrupt flag is not set yet. This occurs between other states and when the TWI module is not involved in a serial transfer. Status 00h indicates that a bus error has occurred during a TWI serial transfer. A bus error is caused when a START or a STOP condition occurs at an illegal position in the format frame. Examples of such illegal positions happen during the serial transfer of an address byte, a data byte, or an acknowledge bit. When a bus error occurs, SI is set. To recover from a bus error, the STO flag must be set and SI must be cleared. This causes the TWI module to enter the not addressed slave mode and to clear the STO flag (no other bits in SSCON are affected). The SDA and SCL lines are released and no STOP condition is transmitted. Notes the TWI module interfaces to the external 2-wire bus via two port pins: SCL (serial clock line) and SDA (serial data line). To avoid low level asserting on these lines when the TWI module is enabled, the output latches of SDA and SLC must be set to logic 1. Table 64. Bit Frequency Configuration Bit Frequency ( kHz) CR2 CR1 CR0 F OSCA= 12 MHz F OSCA = 16 MHz F OSCA divided by 0 0 0 47 62.5 256 0 0 1 53.5 71.5 224 0 1 0 62.5 83 192 0 1 1 75 100 160 1 0 0 - - Unused 1 0 1 100 133.3 120 1 1 0 200 266.6 60 1 1 1 0.5
Figure 33. Format and State in the Master Transmitter Mode MT 4289A–8051–09/03 Successfull transmission to a slave receiver Next transfer started with a repeated start condition Not acknowledge received after the slave address Not acknowledge received after a data byte Arbitration lost in slave address or data byte Arbitration lost and addressed as slave S SLA W A Data A P 08h 18h 28h From master to slave From slave to master A P 20h A or A continues 38h Other master A continues 68h Other master Data A n A P 30h 38h AT89C51ID2 S SLA W 10h Other master A or A continues 78h B0h To corresponding states in slave mode R MR Any number of data bytes and their associated acknowledge bits This number (contained in SSCS) corresponds to a defined state of the 2-wire bus 87
Page 1 and 2:
Features 80C52 Compatible - 8051 In
Page 3 and 4:
Block Diagram Figure 1. Block Diagr
Page 5 and 6:
Table 2. C51 Core SFRs 4289A-8051-0
Page 7 and 8:
Table 8. PCA SFRs 4289A-8051-09/03
Page 9 and 10:
Table 13. SFR Mapping F8h F0h E8h E
Page 11 and 12:
11 AT89C51ID2 4289A-8051-09/03 50 4
Page 13 and 14:
Table 14. Pin Description (Continue
Page 15 and 16:
Oscillators 4289A-8051-09/03 AT89C5
Page 17 and 18:
4289A-8051-09/03 Table 18. PCON Reg
Page 19 and 20:
4289A-8051-09/03 AT89C51ID2 It is a
Page 21 and 22:
4289A-8051-09/03 - FCLK CPU and FCL
Page 23 and 24:
Figure 5. Mode Switching Waveforms
Page 25 and 26:
4289A-8051-09/03 Table 21. CKCON1 R
Page 27 and 28:
4289A-8051-09/03 Table 22. AUXR1 re
Page 29 and 30:
Expanded RAM (XRAM) Figure 7. Inter
Page 31 and 32:
Registers Table 23. AUXR Register A
Page 33 and 34:
Reset Output 4289A-8051-09/03 AT89C
Page 35 and 36: Figure 12. Power Fail Detect Vcc 42
Page 37 and 38: Programmable Clock- Output 4289A-80
Page 39 and 40: Registers Table 24. T2CON Register
Page 41 and 42: Programmable Counter Array PCA 4289
Page 43 and 44: 4289A-8051-09/03 Table 26. CMOD Reg
Page 45 and 46: Figure 16. PCA Interrupt System 428
Page 47 and 48: 4289A-8051-09/03 Table 29. PCA Modu
Page 49 and 50: 4289A-8051-09/03 AT89C51ID2 PCA Cap
Page 51 and 52: Figure 19. PCA High Speed Output Mo
Page 53 and 54: 4289A-8051-09/03 AT89C51ID2 Serial
Page 55 and 56: 4289A-8051-09/03 AT89C51ID2 The SAD
Page 57 and 58: Internal Baud Rate Generator (BRG)
Page 59 and 60: UART Registers Table 40. SADEN Regi
Page 61 and 62: 4289A-8051-09/03 Table 44. T2CON Re
Page 63 and 64: 4289A-8051-09/03 Table 46. BDRCON R
Page 65 and 66: 4289A-8051-09/03 AT89C51ID2 Registe
Page 67 and 68: 4289A-8051-09/03 Table 49. IPL0 Reg
Page 69 and 70: 4289A-8051-09/03 Table 51. IEN1 Reg
Page 71 and 72: 4289A-8051-09/03 Table 54. IPH1 Reg
Page 73 and 74: Power Management 4289A-8051-09/03 A
Page 75 and 76: 4289A-8051-09/03 AT89C51ID2 pins, t
Page 77 and 78: AT89C51ID2 Keyboard Interface The A
Page 79 and 80: 4289A-8051-09/03 Table 59. KBE Regi
Page 81 and 82: 4289A-8051-09/03 AT89C51ID2 2-wire
Page 83 and 84: 4289A-8051-09/03 AT89C51ID2 Descrip
Page 85: 4289A-8051-09/03 AT89C51ID2 When th
Page 89 and 90: Figure 34. Format and State in the
Page 91 and 92: Figure 35. Format and State in the
Page 93 and 94: Table 67. Status in Slave Receiver
Page 95 and 96: Table 68. Status in Slave Transmitt
Page 97 and 98: 4289A-8051-09/03 Bit Number 1 SD1 A
Page 99 and 100: Serial Port Interface (SPI) 4289A-8
Page 101 and 102: Functional Description Figure 38 sh
Page 103 and 104: Figure 40. Data Transmission Format
Page 105 and 106: 4289A-8051-09/03 Figure 43. SPI Int
Page 107 and 108: Serial Peripheral DATa register (SP
Page 109 and 110: WDT During Power Down and Idle 4289
Page 111 and 112: 4289A-8051-09/03 AT89C51ID2 Power-o
Page 113 and 114: 4289A-8051-09/03 Figure 44. Recomme
Page 115 and 116: Registers Table 85. EECON Register
Page 117 and 118: 4289A-8051-09/03 AT89C51ID2 Flash M
Page 119 and 120: 4289A-8051-09/03 Table 88. Program
Page 121 and 122: 4289A-8051-09/03 Table 92. Program
Page 123 and 124: Functional Description Figure 48. B
Page 125 and 126: Boot Process Figure 49. Bootloader
Page 127 and 128: Functional Description 4289A-8051-0
Page 129 and 130: Flow Description 4289A-8051-09/03 A
Page 131 and 132: Write / Program Commands This flow
Page 133 and 134: Display Data Description Figure 55.
Page 135 and 136: Example 4289A-8051-09/03 Read funct
Page 137 and 138:
4289A-8051-09/03 Table 95. ISP Comm
Page 139 and 140:
Table 96. API Call Summary (Continu
Page 141 and 142:
T A = -40°C to +85°C; V SS = 0V;
Page 143 and 144:
External Program Memory Characteris
Page 145 and 146:
External Program Memory Read Cycle
Page 147 and 148:
External Data Memory Write Cycle 42
Page 149 and 150:
AC Testing Input/Output Waveforms F
Page 151 and 152:
Ordering Information 4289A-8051-09/
Page 153 and 154:
VQFP44 4289A-8051-09/03 AT89C51ID2
Page 155 and 156:
PLCC68 4289A-8051-09/03 AT89C51ID2
Page 157 and 158:
4289A-8051-09/03 AT89C51ID2 Pulse W
Page 159:
Atmel Corporation Atmel Operations
show all

Atmel AT89C51ID2 Data Sheet - Keil

Create successful ePaper yourself

Delete template?

Save as template?