Estudo de revestimentos cerâmicos sobre substrato metálico obtido

[90] He, J. L. et al. A comparative study of the cyclic thermal oxidation of PVD nickel
aluminide coating. Surface and Coatings Technology, v. 155, p. 67-79, 2002.
[91] American Society for Metals. ASM Handbook: phase diagram. Materials Park
(OH): ASM International, v. 3, p. 2.49, Ohio, 1996.
[92] Murphy, K. S.; More, K. L.; Lance, M. J. As-deposited mixed zone in TGO
beneath a TBC. Surface and Coatings Technology, v. 146-147, p. 152-161, 2001.
[93] Ruud, J. A.; Bartz, A.; Borom, M. P.; Johnson, C. A. Strenght degradation and
failure mechanisms of EB-PVD TBC. J. Am. Ceram. Soc., v. 7, n. 84, p. 1545-52,
2001.
[94] Sohn, Y. H.; Lee, E. Y.; Nagaraj, B. A.; Biederman, R. R.; Sisson, R. D.
Microstructural characterization of TBC on high pressure turbine blades. Surface and
Coatings Technology, v. 146-147, p. 132-139, 2001.
[95] Sergo, V.; Clarke, D. R. Observation of subcritical spall propagation of a TBC. J.
Am. Ceram. Soc., v. 12, n. 81, p. 3237-42, 1998.
[96] Guo, H.; Bi, X., Gong, S.; Xu, H. Microstructure investigation on gradient porous
TBC prepared by EB-PVD. Scripta Materialia, v. 44, n. 4, p. 683-687, 2001.
[97] Scardi, P.; Leoni, M.; Bertini, L.; Bertamini, L. Residual stress in partiallystabilized-zirconia
TBCs: experimental measurement and modeling. Surface and
Coatings Technology, v. 94-95, p. 82-88, 1997.
[98] Stecura, S. Two-layer thermal barrier coatings, I: effects of composition and
temperature on oxidation behavior and failure. Thin Solid Films, v. 182, n.1-2, p. 121-
139, 1989.
[99] Strauss, D. et al. Oxide scale growth on MCrAlY bond coatings after pulsed
electron beam treatment and deposition of EB-PVD TBC. Surface and Coatings
Technology, v. 135, p. 196-201, 2001.
[100] Haynes, J. A. Potential influence of bond coat impurities and void growth on
premature failure of EB-PVD TBCs. Scripta Materialia, v. 44, n.7, p. 1147-1152,
2001.
[101] Schulz, U. High Temperature Coating, (DLR – German Aerospace Center –
Institute of Materials Research, Alemanha, 2004) Comunicação pessoal
[102] Levi, C. G. (Materials and Mechanical Engineering Department, University of
California, Santa Barbara, 2004) Comunicação pessoal.
[103] Mumm, D. R.; Evans, A. G. On the role of imperfections in the failure of a
thermal barrier coating made by electron beam deposition. Acta Materialia, v. 48, n.8,
p. 1815-1827, 2000.
[104] Begley, M. R. et al. Analysis of a wedge impression test for measuring the
interface toughness between films/coatings and ductile substrates, Acta Materialia, v.
48, n.12, p. 3211-3220, 2000.
173