OP-755 Part 2 Pages 197-401 - Personal Page of GENE SLOVER
OP-755 Part 2 Pages 197-401 - Personal Page of GENE SLOVER
OP-755 Part 2 Pages 197-401 - Personal Page of GENE SLOVER
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
324<br />
inspection purposes. The oil is to be drained from the A-end<br />
tank and the inspection covers 274298-2 are to be removed.<br />
Reach in through the opening and remove the screws 196825-6<br />
from the cover 274284-6. The cover and the valve 274284-7 can<br />
be removed for inspection. Make sure that the valve is free<br />
from bind when reassembled by checking the valve movement<br />
through the opening in the lower end <strong>of</strong> the valve body.<br />
132. The B-end (dr . no. 274249) is built up <strong>of</strong> several<br />
subassemblies, some <strong>of</strong> which maybe removed without completely<br />
dismantling the B-end. The removal and dismantling <strong>of</strong> these<br />
subassemblies will be described separately.<br />
133. To remove the c am support assemb lye - Remove the<br />
large portable plate at the earn end <strong>of</strong> the powder hoist compartment.<br />
Next drain the oil from the camhousing. Remove the<br />
inspection cover 274320-2, which will expose the cams. Remove<br />
the lock washer 200074-8 and the lock nut 271731-3 from the<br />
end <strong>of</strong> the drive shaft 274313-1. Mark the cam support 274322-1<br />
and the gear 274328-9 to insure the reassembly <strong>of</strong> the parts<br />
in the same location. Slip the cam assembly <strong>of</strong>f the end <strong>of</strong><br />
the drive shaft.<br />
134. To dismantle the c am support assembly. - The hoisting<br />
cams are removed by loosening the screws 180226-6, the<br />
heads <strong>of</strong> which project slightly above the surface <strong>of</strong> the clamp<br />
ring 274323-4. The lowering cams are dismantled by removing<br />
the screws 220718-2 from the clamp ring ~74323-2. Remove the<br />
screw 180226-6 from the face <strong>of</strong> the gear 274327-5 and the gear<br />
can be forced <strong>of</strong>f the dowel pins 206485-14. .<br />
135. To reassemble the c am support assembly. -All parts<br />
are to be thoroughly washed in a non-acid cleaning fluid and<br />
are to be assembled in the reverse <strong>of</strong> the dismantling procedure.<br />
The cams are to be adjusted as explainerl in paragraph 80.<br />
136. To remove the rocker arm assemb ly. - Loosen the lock<br />
nut 271665-3 and the lock washer 196733-14. Use bearing lock<br />
nut wrench 220720-2, which may be found in the spare parts<br />
box #1. Tap on the end <strong>of</strong> the shaft 274327-3, and the rocker<br />
arm assembly can be forced <strong>of</strong>f the shaft.<br />
137. To dismantle the rocker arm assembly. - First remove<br />
the two screws 220718-2 and the two screws 180226-7 which<br />
project out <strong>of</strong> the rocker arm, and the hoisting arm 274329-2<br />
can be removed from the hub 274329-1. Next loosen the remaining<br />
two screws 180226-7 and the lowering rocker arm 274328-1<br />
can be dismantled from the hub 274329-1.<br />
138. To reassemble the rocker arm assembly. - The parts<br />
are to be thoroughly cleaned, and are to be reassembled in