OP-755 Part 2 Pages 197-401 - Personal Page of GENE SLOVER
OP-755 Part 2 Pages 197-401 - Personal Page of GENE SLOVER
OP-755 Part 2 Pages 197-401 - Personal Page of GENE SLOVER
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
327<br />
147 . Tor e ass e mb let h e cam hau8 i ng (dr. no . 274326~1) .<br />
The parts are to be washed in a non-acid cleaning fluid and<br />
are to be reassembled in reverse <strong>of</strong> the dismantling procedure.<br />
<strong>Part</strong> 274334-13 is to be as sembled into the oil seal 274338-8<br />
and the bearing 274337-11 before the cam housing assembly is<br />
slipped over the drive shaft. Make sure that the gasket<br />
274329-4 is in place before the housing is assembled to the<br />
shaft. After the parts are reassembled, they are to be adjusted<br />
as explained in the instructions.<br />
148. To remove the hoisting drum (dr . no. 274325-1). -<br />
First remove the cam housing assembly. Next disconnect the<br />
cable from the drum by removing the slotted nut 274339-1 and<br />
the collar 274328-11. Remove the cable clamps and pull. the<br />
cable out <strong>of</strong> the slotted holes in the drum. Removethe hoisting<br />
drum from the shaft 274314-1.<br />
149. To dismantle the hoisting drum (dr. no. 274325-1).<br />
After the drum has been removed, the screws 200075-6, which<br />
secure the ratchet 274317-4 to the drum are to be removed.<br />
The ratchet can now be forced <strong>of</strong>f the dowel pins 206664-6.<br />
150 . Tor e ass e mb let h e ti a i s tin g drum (dr , no. 274325 -1) .<br />
The parts are to be reassembled in reverse <strong>of</strong> the dismantling<br />
procedure except that the hoisting cable may be attached to<br />
the hoist d-rum, if desired, after the earn housing has been reassembled.<br />
Before assembling the drum on the shaft, wire hooks<br />
are to be formed which will hook over the edge <strong>of</strong>' the brake<br />
drum and into the holes on the ratchet dogs 274317-5, to hold<br />
the dogs clear <strong>of</strong> ratchet 274318-2. After the drum has been<br />
assembled far enough on the shaft to permit the dogs to engage,<br />
the wire hooks are to be removed and the drum pushed up<br />
against its retaining face.<br />
1'S1. To remove the brake drum (dr , no. 274320-1) - First<br />
remove the cam housing and hoisting drum 274325-1 and then the<br />
brake band assembly 274307, as explained previously. The brake<br />
drum can nowbe slipped over the end <strong>of</strong> the drive shaft 274314-1.<br />
152. To dismantle the brake drum (dr , no. 274320-1). -<br />
Remove the slotted nuts 274339-7, and the ratchet dog support<br />
pins 274322-2 can be driven out <strong>of</strong> the brake drum. The springs<br />
274317-7 can be disconnected from the ratchet dogs.<br />
153.<br />
The parts<br />
are to be<br />
To reassemble the brake drum (dr. no. 274320-1)~ -<br />
are to be washed in a non-acid cleaning fluid and<br />
reassembled in reverse <strong>of</strong> the dismantling procedure.<br />
CAUTION: Be sure that all oil has been carefully<br />
cleaned <strong>of</strong>f the brake drum and<br />
the brake band assembly while assembling<br />
these parts.