Programming manual M238 | 3 MB - BERGER - POSITEC

More documents

Recommendations

Info

Function and Function Block Representation 234 EIO0000000384 04/2012
Overview Modicon M238 Logic Controller Functions to get/set serial line configuration in user program EIO0000000384 04/2012 Functions to Get/Set Serial Line Configuration in User Program C This section describes the functions to get/set the serial line configuration in your program. To use these functions, you must add the M2xx Communication library. For further information on adding a library, refer to the SoMachine Programming Guide (see SoMachine, Programming Guide). What’s in this Chapter? This chapter contains the following topics: Topic Page GetSerialConf: Get the Serial Line Configuration 236 SetSerialConf: Change the Serial Line Configuration 237 SERIAL_CONF: Structure of the Serial Line Configuration Data Type 239 EIO0000000384 04/2012 235
Page 1 and 2:
EIO0000000384.04 Modicon M238 Logic
Page 3 and 4:
Table of Contents Safety Informatio
Page 5 and 6:
Chapter 16 Loader Device Accessory
Page 7 and 8:
Important Information NOTICE Safety
Page 9 and 10:
At a Glance Document Scope Validity
Page 11 and 12:
Product Related Information User Co
Page 13 and 14:
Modicon M238 Logic Controller M238
Page 15 and 16:
Modicon M238 Logic Controller How t
Page 17 and 18:
Device Tree How to Configure the Co
Page 19 and 20:
Libraries Introduction Modicon M238
Page 21 and 22:
Modicon M238 Logic Controller Suppo
Page 23 and 24:
Introduction Modicon M238 Logic Con
Page 25 and 26:
Customer Area 1000 kbytes TM238LDD2
Page 27 and 28:
System Variables Library Sizes Memo
Page 29 and 30:
Memory Mapping Relocation Table Edi
Page 31 and 32:
Page 33 and 34:
Task Configuration Screen Tasks Scr
Page 35 and 36:
Task Types Introduction Cyclic Task
Page 37 and 38:
Tasks External Event Task This type
Page 39 and 40:
Task Priorities Introduction Tasks
Page 41 and 42:
Default Task Configuration Tasks De
Page 43 and 44:
Page 45 and 46:
Note 1 Note 2 Note 3 Note 4 Note 5a
Page 47 and 48:
Note 8 Note 9 Controller States and
Page 49 and 50:
7.2 Controller States Description C
Page 51 and 52:
Controller States and Behaviors Tas
Page 53 and 54:
7.3 State Transitions and System Ev
Page 55 and 56:
Controller States and Behaviors Ini
Page 57 and 58:
Commanding State Transitions Run Co
Page 59 and 60:
Reset Cold Reset Origin Controller
Page 61 and 62:
Controller States and Behaviors 9.
Page 63 and 64:
Error Detection, Types, and Managem
Page 65 and 66:
Page 67 and 68:
Tab Descriptions Controller Device
Page 69 and 70:
PLC Settings Overview The figure be
Page 71 and 72:
Services Services Tab The Services
Page 73 and 74:
Overview Modicon M238 Logic Control
Page 75 and 76:
M238 Embedded Functions HSC Configu
Page 77 and 78:
M238 Embedded Functions I/O Configu
Page 79 and 80:
Configuration Parameters For each d
Page 81 and 82:
M238 Embedded Functions PTO_PWM Con
Page 83 and 84:
Modicon M238 Logic Controller Expan
Page 85 and 86:
Modicon M238 Logic Controller CANop
Page 87 and 88:
CANopen Configuration CANopen Opera
Page 89 and 90:
Page 91 and 92:
General Functional Description AS-I
Page 93 and 94:
The following table describes the d
Page 95 and 96:
Add an AS-Interface Master Module I
Page 97 and 98:
Configure an AS-Interface Master In
Page 99 and 100:
Tab Name Configuration Window Descr
Page 101 and 102:
Step Action AS-Interface Configurat
Page 103 and 104:
AS-Interface Configuration Add a Sl
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Configure an AS-Interface Slave Int
Page 111 and 112:
AS-Interface Configuration The tabl
Page 113 and 114:
Modification of Slave Address At a
Page 115 and 116:
Step Description AS-Interface Confi
Page 117 and 118:
AS-Interface Configuration Diagnost
Page 119 and 120:
Diagnostic of AS-Interface Slave De
Page 121 and 122:
Configuration of a Replaced AS-Inte
Page 123 and 124:
Page 125 and 126:
Step Action 3 Click the Physical Se
Page 127 and 128:
Serial Line Configuration The follo
Page 129 and 130:
Configure the Manager To configure
Page 131 and 132:
SoMachine Network Manager Introduct
Page 133 and 134:
Modbus IOScanner Introduction Seria
Page 135 and 136:
Adding a Device on the Modbus IOSca
Page 137 and 138:
Step Action To configure the Modbus
Page 139 and 140:
Step Action To configure your Modbu
Page 141 and 142:
Serial Line Configuration These scr
Page 143 and 144:
Modbus Manager Introduction Serial
Page 145 and 146:
Modbus Master Modbus Slave Serial L
Page 147 and 148:
Adding a Modem Serial Line Configur
Page 149 and 150:
Modicon M238 Logic Controller Ether
Page 151 and 152:
Step Action Comment 3 Select 499TWD
Page 153 and 154:
Step Action Comment 3 Enter the val
Page 155 and 156:
Page 157 and 158:
M238 - Connecting the Modicon M238
Page 159 and 160:
Active Path of the Controller Intro
Page 161 and 162:
Page 163 and 164:
Loader Device AccessoryDescription
Page 165 and 166:
Physical Description Overview 1 Bat
Page 167 and 168:
LED Status and Diagnostic LED Statu
Page 169 and 170:
Firmware and SoMachine Software Com
Page 171 and 172:
Loader Device Accessory 16.2 Upload
Page 173 and 174:
Upload From the Controller to the U
Page 175 and 176:
Interrupting a download can erase t
Page 177 and 178:
16.4 Other Functionalities What’s
Page 179 and 180:
Update the Firmware of the Loader D
Page 181 and 182:
Page 183 and 184: Updating the firmware requires one
Page 185 and 186: Updating Through USB Introduction U
Page 187 and 188: Launching the Exec Loader Wizard In
Page 189 and 190: Step 2 - Settings Selecting Setting
Page 191 and 192: Step 3 - File and Device Exec Prope
Page 193 and 194: Step 4 - Transfer Progress Overview
Page 195 and 196: Modicon M238 Logic Controller Modic
Page 197 and 198: Check Action Resolution: Modicon M2
Page 199 and 200: Modicon M238 Logic Controller - Tro
Page 201 and 202: Modicon M238 Logic Controller - Tro
Page 203 and 204: Frequently Asked Questions Modicon
Page 205 and 206: Overview Modicon M238 Logic Control
Page 209 and 210: ASI_CmdSetAutoAddressing AS-Interfa
Page 211 and 212: ASI_CmdSetDataExchange Description
Page 213 and 214: ASI_CmdSetOfflineMode Description G
Page 215 and 216: ASI_MasterStatusCheck Description G
Page 217 and 218: ASI_SlaveAddressChange Description
Page 219 and 220: ERROR: Detected Error Codes The ERR
Page 221 and 222: The following table describes the o
Page 223 and 224: Output Type Comment LAS ARRAY[0..7]
Page 225 and 226: The following table describes the o
Page 229 and 230: How to Use a Function or a Function
Page 231 and 232: Step Action Function and Function B
Page 233: Function and Function Block Represe
Page 237 and 238: SetSerialConf: Change the Serial Li
Page 239 and 240: Functions to get/set serial line co
Page 241 and 242: Modicon M238 Logic Controller M238
Page 243 and 244: application source ARP ASCII BOOTP
Page 245 and 246: controller cyclic task data log DHC
Page 247 and 248: Flash Memory FTP function block Glo
Page 249 and 250: LD located variable MAC address MAS
Page 251 and 252: periodic execution persistent data
Page 253 and 254: SDO sequential function chart See S
Page 255 and 256: Modicon M238 Logic Controller Index
show all

Programming manual M238 | 3 MB - BERGER - POSITEC

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?