FR60 MB91460E Series - Microcontrollers - Fujitsu

More documents

Recommendations

Info

MB91460E Series ■ ELECTRICAL CHARACTERISTICS 1. Absolute maximum ratings Parameter Symbol Min Rating Max Unit Remarks Power supply slew rate ⎯ ⎯ 50 V/ms Power supply voltage 1* 1 VDD5R − 0.3 + 6.0 V Power supply voltage 2* 1 VDD5 − 0.3 + 6.0 V Power supply voltage 3* 1 HVDD5 − 0.3 + 6.0 V Power supply voltage 4* 1 VDD35 − 0.3 + 6.0 V Relationship of the supply voltages HVDD5 AVCC5 VDD5-0.3 VDD5+0.3 V SMC mode VSS5-0.3 VDD5+0.3 V VDD5-0.3 VDD5+0.3 V VSS5-0.3 VDD5+0.3 V General purpose port mode At least one pin of the Ports 25 to 29 (SMC, ANn) is used as digital input or output. All pins of the Ports 25 to 29 (SMC, ANn) follow the condition of VIA Analog power supply voltage* 1 AVCC5 − 0.3 + 6.0 V *2 Analog reference power supply voltage* 1 AVRH5 − 0.3 + 6.0 V *2 Input voltage 1* 1 VI1 Vss5 − 0.3 VDD5 + 0.3 V Input voltage 2* 1 VI2 Vss5 − 0.3 VDD35 + 0.3 V External bus Input voltage 3* 1 VI3 HVss5 − 0.3 HVDD5 + 0.3 V Stepper motor controller Analog pin input voltage* 1 VIA AVss5 − 0.3 AVcc5 + 0.3 V Output voltage 1* 1 VO1 Vss5 − 0.3 VDD5 + 0.3 V Output voltage 2* 1 VO2 Vss5 − 0.3 VDD35 + 0.3 V External bus Output voltage 3* 1 VO3 HVss5 − 0.3 HVDD5 + 0.3 V Stepper motor controller Maximum clamp current ICLAMP − 4.0 + 4.0 mA *3 Total maximum clamp current Σ |ICLAMP| ⎯ 20 mA *3 “L” level maximum output current* 4 IOL ⎯ ⎯ 10 40 mA mA Stepper motor controller “L” level average output current* 5 IOLAV ⎯ ⎯ 8 30 mA mA Stepper motor controller “L” level total maximum output current “L” level total average output current* 6 “H” level maximum output current* 4 ΣIOL ΣIOLAV IOH ⎯ 100 mA ⎯ 360 mA Stepper motor controller ⎯ 50 mA ⎯ 230 mA Stepper motor controller ⎯ − 10 mA ⎯ − 40 mA Stepper motor controller 150 DS705-00002-1v3-E
“H” level average output current* 5 Parameter Symbol “H” level total maximum output current “H” level total average output current* 6 IOHAV ΣIOH ΣIOHAV MB91460E Series Min Rating Max Unit Remarks ⎯ − 4 mA ⎯ − 30 mA Stepper motor controller ⎯ − 100 mA ⎯ − 360 mA Stepper motor controller ⎯ − 25 mA ⎯ − 230 mA Stepper motor controller ⎯ 1100 *8 mW at TA ≤ 85 °C Permitted power dissipation *7 PD ⎯ 1100 *8 mW at TA ≤ 105 °C, no Flash program/erase *9 ⎯ 555 *8 mW at TA ≤ 105 °C Operating temperature TA − 40 + 105 °C Storage temperature Tstg − 55 + 150 °C *1 : The parameter is based on VSS5 = HVSS5 = AVSS5 = 0.0 V. *2 : AVCC5 and AVRH5 must not exceed VDD5 + 0.3 V. *3 : • Use within recommended operating conditions. • Use with DC voltage (current). •+B signals are input signals that exceed the VDD5 voltage. +B signals should always be applied by connecting a limiting resistor between the +B signal and the microcontroller. • The value of the limiting resistor should be set so that the current input to the microcontroller pin does not exceed the rated value at any time , either instantaneously or for an extended period, when the +B signal is input. • Note that when the microcontroller drive current is low, such as in the low power consumption modes, the +B input potential can increase the potential at the power supply pin via a protective diode, possibly affecting other devices. • Note that if the +B signal is input when the microcontroller is off (not fixed at 0 V), power is supplied through the +B input pin; therefore, the microcontroller may partially operate. • Note that if the +B signal is input at power-on, since the power is supplied through the pin, the power-on reset may not function in the power supply voltage. DS705-00002-1v3-E 151
Page 1 and 2:
FUJITSU SEMICONDUCTOR DATA SHEET 32
Page 3 and 4:
MB91460E Series (Continued) • Rea
Page 5 and 6:
MB91460E Series Sound Generator 1 c
Page 7 and 8:
MB91460E Series DS705-00002-1v3-E 7
Page 9 and 10:
(Continued) Pin no. Pin name I/O 66
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
2. Power supply/Ground pins MB91460
Page 17 and 18:
Type Circuit Remarks MB91460E Serie
Page 19 and 20:
Type Circuit Remarks G Mask ROM and
Page 21 and 22:
Type Circuit Remarks M CMOS level t
Page 23 and 24:
(Continued) Example of using opposi
Page 25 and 26:
■ NOTES ON DEBUGGER 1. Execution
Page 27 and 28:
■ A/D CONVERTER / RANGE COMPARATO
Page 29 and 30:
3. Block Diagram of A/D Converter T
Page 31 and 32:
1. On MB91F467E, ADC1 does not exis
Page 33 and 34:
• ADCS1 : Access: Half-word, Byte
Page 35 and 36:
MB91460E Series [bit 9] STRT (Start
Page 37 and 38:
4.2. Common Data Register (ADCR1, A
Page 39 and 40:
4.5. A/D Channel Setting Register (
Page 41 and 42:
5.2. Range Comparator Registers The
Page 43 and 44:
5.2.3. Inverted Range Selection reg
Page 45 and 46:
MB91460E Series The interrupt condi
Page 47 and 48:
6. Operation of A/D Converter MB914
Page 49 and 50:
6.5. Scan Conversion The following
Page 51 and 52:
MB91460E Series The automatic inter
Page 53 and 54:
■ CLOCK SUPERVISOR (New Feature)
Page 55 and 56:
2.1. Clock Supervisor Control Regis
Page 57 and 58:
3. Block Diagram Clock Supervisor M
Page 59 and 60:
MB91460E Series Figure 0-4 Timing D
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
4.3. Re-enabling the RC-oscillator
Page 67 and 68:
MB91460E Series Figure 0-11 Timing
Page 69 and 70:
Timing Diagram: Waking up from Sub
Page 71 and 72:
4.9. RTC mode (STOP mode with Real
Page 73 and 74:
4.11. Check if reset was asserted b
Page 75 and 76:
■ MB91460E Series DS705-00002-1v3
Page 77 and 78:
2. Standby RAM MB91460E Series MB91
Page 79 and 80:
3.3. EXTE: Shutdown recovery extern
Page 81 and 82:
[bit 1] RTCF: Real Time Clock recov
Page 83 and 84:
3.6. EXTLV1/2: Shutdown recovery ex
Page 85 and 86:
4.1.3. Shutdown with Real Time Cloc
Page 87 and 88:
4.1.8. External Interrupts: Level o
Page 89 and 90:
4.3. Determining the Reset Source a
Page 91 and 92:
4.5. I/O Behaviour in Shutdown Duri
Page 93 and 94:
3. Programming model 3.1. Basic pro
Page 95 and 96:
4.3. CCR (Condition Code Register)
Page 97 and 98:
■ EMBEDDED PROGRAM/DATA MEMORY (F
Page 99 and 100: 3.2. Flash access timing settings i
Page 101 and 102: 4. Parallel Flash programming mode
Page 103 and 104: 5. Poweron Sequence in parallel pro
Page 105 and 106: 6.3. Security Vector FSV2 MB91460E
Page 107 and 108: ■ MEMORY MAPS 1. MB91F467EA 00000
Page 109 and 110: Address 000000H 000004H 000008H Reg
Page 111 and 112: (Continued) Address 0000A0H Registe
Page 113 and 114: (Continued) Address 000180H Reserve
Page 115 and 116: (Continued) Address 000200H 000204H
Page 117 and 118: (Continued) Address 000348H 00034CH
Page 119 and 120: (Continued) Address 00048CH 000490H
Page 121 and 122: (Continued) Address + 0 + 1 Registe
Page 123 and 124: Address 000704H 000708H 00070CH 000
Page 125 and 126: (Continued) Address 000D80H 000D84H
Page 127 and 128: (Continued) Address 000E80H 000E84H
Page 129 and 130: (Continued) Address 002000H to 006F
Page 131 and 132: (Continued) Address 00C080H 00C084H
Page 133 and 134: (Continued) Address 00C1A0H 00C1A4H
Page 135 and 136: Address 00F09CH 00F0A0H 00F0A4H 00F
Page 137 and 138: 32bit read/write dat[31:0] dat[31:0
Page 139 and 140: (Continued) Interrupt Decimal Inter
Page 141 and 142: (Continued) Interrupt Decimal Inter
Page 143 and 144: ■ RECOMMENDED SETTINGS 1. PLL and
Page 145 and 146: MB91460E Series (Continued) Modulat
Page 147 and 148: MB91460E Series (Continued) Modulat
Page 149: (Continued) Modulation Degree (k) R
Page 153 and 154: 2. Recommended operating conditions
Page 155 and 156: 3. DC characteristics MB91460E Seri
Page 157 and 158: Parameter Symbol Analog inputleakag
Page 159 and 160: MB91460E Series 4. A/D converter ch
Page 161 and 162: Digital output 3FFH 3FEH 3FDH 004H
Page 163 and 164: 5. Alarm comparator characteristics
Page 165 and 166: 7. AC characteristics 7.1. Clock ti
Page 167 and 168: 7.3. LIN-USART Timings at VDD5 = 3.
Page 169 and 170: 7.4. I 2 C AC Timings at VDD5 = 3.0
Page 171 and 172: 7.5. Free-run timer clock Input pul
Page 173 and 174: MCLKO CSXn delayed CSXn ASX ADDRESS
Page 175 and 176: MCLKO MCLKI CSXn WRXn (as byte enab
Page 177 and 178: MB91460E Series 7.7.4. Synchronous
Page 179 and 180: MB91460E Series 7.7.6. Asynchronous
Page 181 and 182: 7.7.8. RDY waitcycle insertion Para
Page 183 and 184: 7.7.10. Clock relationships MB91460
Page 185 and 186: MCLKO DACKX DEOP delayed DACKX dela
Page 187 and 188: MCLKO CSXn delayed CSXn ASX ADDRESS
Page 189 and 190: MCLKO MCLKI CSXn WRXn (as byte enab
Page 191 and 192: MB91460E Series 7.8.4. Synchronous
Page 193 and 194: MB91460E Series 7.8.6. Asynchronous
Page 195 and 196: 7.8.8. RDY waitcycle insertion Para
Page 197 and 198: 7.8.10. Clock relationships MCLKO
Page 199 and 200: MCLKO DACKX DEOP delayed DACKX dela
Page 201 and 202:
■ PACKAGE DIMENSION 208-pin plast
Page 203 and 204:
Version/ Date Ver. 0.8 2009-10-19 V
Page 205 and 206:
■ CHANGES IN THIS EDITION DS705-0
Page 207 and 208:
MEMO MB91460E Series DS705-00002-1v
Page 209:
MB91460E Series DS705-00002-1v3-E 2
show all

FR60 MB91460E Series - Microcontrollers - Fujitsu

Create successful ePaper yourself

Delete template?

Save as template?