FR60 MB91460E Series - Microcontrollers - Fujitsu

More documents

Recommendations

Info

MB91460E Series 4.7. TBR (Table Base Register) bit 31 The table base register stores the starting address of the vector table used in EIT processing. The initial value at reset is 000FFC00H. 4.8. RP (Return Pointer) bit 31 The return pointer stores the address for return from subroutines. During execution of a CALL instruction, the PC value is transferred to this RP register. During execution of a RET instruction, the contents of the RP register are transferred to PC. The initial value at reset is undefined. 4.9. USP (User Stack Pointer) bit 31 The user stack pointer, when the S flag is “1”, this register functions as the R15 register. • The USP register can also be explicitly specified. The initial value at reset is undefined. • This register cannot be used with RETI instructions. 4.10. Multiply & divide registers bit 31 MDH MDL These registers are for multiplication and division, and are each 32 bits in length. The initial value at reset is undefined. 96 DS705-00002-1v3-E bit 0 bit 0 bit 0 Initial value 000FFC00H Initial value XXXXXXXXH Initial value XXXXXXXXH bit 0
■ EMBEDDED PROGRAM/DATA MEMORY (FLASH) MB91460E Series 1. Flash features • MB91F467EA: 1088 Kbytes (16 × 64 Kbytes + 8 × 8 Kbytes) = 8.5 Mbits • Programmable wait state for read/write access • Flash and Boot security with security vector at 0x0014:8000 - 0x0014:800F • Boot security • Basic specification: Same as MBM29LV400TC (except size and part of sector configuration) 2. Operation modes (1) 64-bit CPU mode: • CPU reads and executes programs in word (32-bit) length units. • Flash writing is not possible. • Actual Flash Memory access is performed in d-word (64-bit) length units. (2) 32-bit CPU mode : • CPU reads, writes and executes programs in word (32-bit) length units. • Actual Flash Memory access is performed in word (32-bit) length units. (3) 16-bit CPU mode : • CPU reads and writes in half-word (16-bit) length units. • Program execution from the Flash is not possible. • Actual Flash Memory access is performed in half-word (16-bit) length units. Note: The operation mode of the flash memory can be selected using a Boot-ROM function. The function start address is 0xBF60. The parameter description is given in the Hardware Manual in chapter 54.6 "Flash Access Mode Switching". DS705-00002-1v3-E 97
Page 1 and 2:
FUJITSU SEMICONDUCTOR DATA SHEET 32
Page 3 and 4:
MB91460E Series (Continued) • Rea
Page 5 and 6:
MB91460E Series Sound Generator 1 c
Page 7 and 8:
MB91460E Series DS705-00002-1v3-E 7
Page 9 and 10:
(Continued) Pin no. Pin name I/O 66
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
2. Power supply/Ground pins MB91460
Page 17 and 18:
Type Circuit Remarks MB91460E Serie
Page 19 and 20:
Type Circuit Remarks G Mask ROM and
Page 21 and 22:
Type Circuit Remarks M CMOS level t
Page 23 and 24:
(Continued) Example of using opposi
Page 25 and 26:
■ NOTES ON DEBUGGER 1. Execution
Page 27 and 28:
■ A/D CONVERTER / RANGE COMPARATO
Page 29 and 30:
3. Block Diagram of A/D Converter T
Page 31 and 32:
1. On MB91F467E, ADC1 does not exis
Page 33 and 34:
• ADCS1 : Access: Half-word, Byte
Page 35 and 36:
MB91460E Series [bit 9] STRT (Start
Page 37 and 38:
4.2. Common Data Register (ADCR1, A
Page 39 and 40:
4.5. A/D Channel Setting Register (
Page 41 and 42:
5.2. Range Comparator Registers The
Page 43 and 44:
5.2.3. Inverted Range Selection reg
Page 45 and 46: MB91460E Series The interrupt condi
Page 47 and 48: 6. Operation of A/D Converter MB914
Page 49 and 50: 6.5. Scan Conversion The following
Page 51 and 52: MB91460E Series The automatic inter
Page 53 and 54: ■ CLOCK SUPERVISOR (New Feature)
Page 55 and 56: 2.1. Clock Supervisor Control Regis
Page 57 and 58: 3. Block Diagram Clock Supervisor M
Page 59 and 60: MB91460E Series Figure 0-4 Timing D
Page 65 and 66: 4.3. Re-enabling the RC-oscillator
Page 67 and 68: MB91460E Series Figure 0-11 Timing
Page 69 and 70: Timing Diagram: Waking up from Sub
Page 71 and 72: 4.9. RTC mode (STOP mode with Real
Page 73 and 74: 4.11. Check if reset was asserted b
Page 75 and 76: ■ MB91460E Series DS705-00002-1v3
Page 77 and 78: 2. Standby RAM MB91460E Series MB91
Page 79 and 80: 3.3. EXTE: Shutdown recovery extern
Page 81 and 82: [bit 1] RTCF: Real Time Clock recov
Page 83 and 84: 3.6. EXTLV1/2: Shutdown recovery ex
Page 85 and 86: 4.1.3. Shutdown with Real Time Cloc
Page 87 and 88: 4.1.8. External Interrupts: Level o
Page 89 and 90: 4.3. Determining the Reset Source a
Page 91 and 92: 4.5. I/O Behaviour in Shutdown Duri
Page 93 and 94: 3. Programming model 3.1. Basic pro
Page 95: 4.3. CCR (Condition Code Register)
Page 99 and 100: 3.2. Flash access timing settings i
Page 101 and 102: 4. Parallel Flash programming mode
Page 103 and 104: 5. Poweron Sequence in parallel pro
Page 105 and 106: 6.3. Security Vector FSV2 MB91460E
Page 107 and 108: ■ MEMORY MAPS 1. MB91F467EA 00000
Page 109 and 110: Address 000000H 000004H 000008H Reg
Page 111 and 112: (Continued) Address 0000A0H Registe
Page 113 and 114: (Continued) Address 000180H Reserve
Page 115 and 116: (Continued) Address 000200H 000204H
Page 117 and 118: (Continued) Address 000348H 00034CH
Page 119 and 120: (Continued) Address 00048CH 000490H
Page 121 and 122: (Continued) Address + 0 + 1 Registe
Page 123 and 124: Address 000704H 000708H 00070CH 000
Page 125 and 126: (Continued) Address 000D80H 000D84H
Page 127 and 128: (Continued) Address 000E80H 000E84H
Page 129 and 130: (Continued) Address 002000H to 006F
Page 131 and 132: (Continued) Address 00C080H 00C084H
Page 133 and 134: (Continued) Address 00C1A0H 00C1A4H
Page 135 and 136: Address 00F09CH 00F0A0H 00F0A4H 00F
Page 137 and 138: 32bit read/write dat[31:0] dat[31:0
Page 139 and 140: (Continued) Interrupt Decimal Inter
Page 141 and 142: (Continued) Interrupt Decimal Inter
Page 143 and 144: ■ RECOMMENDED SETTINGS 1. PLL and
Page 145 and 146: MB91460E Series (Continued) Modulat
Page 147 and 148:
MB91460E Series (Continued) Modulat
Page 149 and 150:
(Continued) Modulation Degree (k) R
Page 151 and 152:
“H” level average output curren
Page 153 and 154:
2. Recommended operating conditions
Page 155 and 156:
3. DC characteristics MB91460E Seri
Page 157 and 158:
Parameter Symbol Analog inputleakag
Page 159 and 160:
MB91460E Series 4. A/D converter ch
Page 161 and 162:
Digital output 3FFH 3FEH 3FDH 004H
Page 163 and 164:
5. Alarm comparator characteristics
Page 165 and 166:
7. AC characteristics 7.1. Clock ti
Page 167 and 168:
7.3. LIN-USART Timings at VDD5 = 3.
Page 169 and 170:
7.4. I 2 C AC Timings at VDD5 = 3.0
Page 171 and 172:
7.5. Free-run timer clock Input pul
Page 173 and 174:
MCLKO CSXn delayed CSXn ASX ADDRESS
Page 175 and 176:
MCLKO MCLKI CSXn WRXn (as byte enab
Page 177 and 178:
MB91460E Series 7.7.4. Synchronous
Page 179 and 180:
MB91460E Series 7.7.6. Asynchronous
Page 181 and 182:
7.7.8. RDY waitcycle insertion Para
Page 183 and 184:
7.7.10. Clock relationships MB91460
Page 185 and 186:
MCLKO DACKX DEOP delayed DACKX dela
Page 187 and 188:
MCLKO CSXn delayed CSXn ASX ADDRESS
Page 189 and 190:
MCLKO MCLKI CSXn WRXn (as byte enab
Page 191 and 192:
MB91460E Series 7.8.4. Synchronous
Page 193 and 194:
MB91460E Series 7.8.6. Asynchronous
Page 195 and 196:
7.8.8. RDY waitcycle insertion Para
Page 197 and 198:
7.8.10. Clock relationships MCLKO
Page 199 and 200:
MCLKO DACKX DEOP delayed DACKX dela
Page 201 and 202:
■ PACKAGE DIMENSION 208-pin plast
Page 203 and 204:
Version/ Date Ver. 0.8 2009-10-19 V
Page 205 and 206:
■ CHANGES IN THIS EDITION DS705-0
Page 207 and 208:
MEMO MB91460E Series DS705-00002-1v
Page 209:
MB91460E Series DS705-00002-1v3-E 2
show all

FR60 MB91460E Series - Microcontrollers - Fujitsu

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?