DiMAGE Scan Elite II Hardware OM - Konica Minolta Photo Imaging ...

More documents

Recommendations

Info

35mm 35mm 35mm FOR PROPER AND SAFE USE Please read and understand each caution before using this product. Keep inflammable products away from the scanner WARNING Take the product to a Minolta Service Facility when repairs are required. Basic operation: • Do not use the product near inflammable gases or liquids such as gasoline, benzine, or paint thinner. Do not use inflammable products such as alcohol, benzine, or paint thinner to clean the product. The use of inflammable cleaners and solvents may cause an explosion or fire. • Do not operate this product or handle the power cord with wet hands. Do not place a container with liquid near the product. If liquid comes in contact with the product, immediately unplug the unit. The continued use of a product exposed to a liquid may cause damage or injury through fire or electric shock. • Do not insert hands, inflammable objects, or metal objects such as paper clips or staples through the front door of this product. It may cause damage or injury through fire or electric shock. Discontinue use if an object enters the product. Minolta AC Adaptor AC-U10 shock. Power supply: • Use only the specified AC adaptor (Delta Electronics ADP-20LB REV:B) within the voltage range indicated on the adaptor unit. An inappropriate adaptor or current may cause damage or injury through fire or electric • Do not damage, twist, modify, heat, or place heavy objects on the power cord. A damaged cord may cause damage or injury through fire or electric shock. • When unplugging the unit, do not pull on the power cord. Hold the plug when removing the cord from an outlet. Additional warnings: • Do not disassemble this product. Electric shock may cause injury if a high-voltage circuit inside the product is touched. Take the product to a Minolta Service Facility when repairs are required. • Immediately unplug the unit and discontinue use if the product is dropped or subjected to an impact in which the interior is exposed. The continued use of a damaged product may cause injuries or fire. 6
35 m 35mm 35mm • Store this product out of reach of children. Be careful when around children, not to harm them with the product or parts. • If the product emits a strange odour, heat, or smoke, discontinue use. Immediately unplug the power cord taking care not to burn yourself. The continued use of a damaged product or parts may cause injury or fire. CAUTION • The required operating environment must be between 10°C and 35°C with less than 80% humidity. A sudden change in temperature can cause condensation inside the product, which may result in electric shock or fire. When the product is subjected to a drastic change in temperature, allow the product time to come to equilibrium with the surrounding environment. Power supply: • Insert the plug securely into the electrical outlet. • Do not obstruct access to the AC adaptor; this can hinder the unplugging of the unit in emergencies. Basic operation: • This product should only be operated in the upright position. Inappropriate placement may result in fire. • Do not cover the AC adaptor. A fire may result. • Periodically check that the power cord is not damaged and the plug is clean. Dust and dirt that may collect between the prongs of the plugs may result in fire. • Do not use if the cord is damaged. • Damage or injury through fire or electric shock may result if the product is used or stored in the following conditions: In humid or dusty environments. In direct sunlight or hot environments. In smoky or oily areas. In unventilated areas. On unstable or unlevel surfaces. Disconnect power supply when not in use. • Unplug the product when cleaning or when the product is not in use for long periods. Additional cautions: • Do not move, obstruct, or touch the film holder when scanning. The product or scanned images can be damaged. • Do not use a brush or air brush to clean the interior of the product. 7
Page 1 and 2: STANDARD SCAN UTILITY EASY SCAN UTI
Page 3 and 4: OTHER DISPLAYS IN THE PRESCAN WINDO
Page 5: This mark certifies that this produ
Page 9 and 10: INSTALLING THE UTILITY SOFTWARE To
Page 11 and 12: 4 Click “Next” to view the lice
Page 13 and 14: 10 Any software that is running mus
Page 15 and 16: 6 Read the cautions on the setup sc
Page 17 and 18: 1 Turn on the computer to start the
Page 19 and 20: NAMES OF PARTS 35mm film-holder mar
Page 21 and 22: DISCONNECTING THE CABLE WITH WINDOW
Page 23 and 24: 2. LOADING THE FILM HOLDER Using th
Page 25 and 26: 2 CAUTION • Do not remove the APS
Page 27 and 28: 5. MAKING AN INDEX SCAN An index sc
Page 29 and 30: TURNING OFF THE SCANNER 1 Press the
Page 31 and 32: 1. LAUNCHING THE STANDARD SCAN UTIL
Page 33 and 34: 2. SETTING UP THE SCANNER MAIN WIND
Page 35 and 36: Multi-sample list box Multi-samplin
Page 37 and 38: 5. INDEX SCAN The index scan is a l
Page 39 and 40: ROTATING OR FLIPPING THE INDEX FRAM
Page 41 and 42: SAVING AN INDEX FILE The index thum
Page 43 and 44: MAKING A PRESCAN 1 Select the index
Page 45 and 46: PRESCANNING THE CROPPED IMAGE Click
Page 47 and 48: ZOOMING The prescan image can be en
Page 49 and 50: AE LOCK The exposure obtained with
Page 51 and 52: CROPPING APS IMAGES When APS film f
Page 53 and 54: TONE CURVES AND HISTOGRAM Click the
Page 55 and 56: CHANGING THE TONE CURVES 1 Place th
Page 57 and 58:
INCREASING THE CONTRAST OF AN IMAGE
Page 59 and 60:
6 Click a neutral area of the image
Page 61 and 62:
COLOUR CORRECTIONS WITH THE HISTOGR
Page 63 and 64:
HUE/SATURATION/LIGHTNESS CORRECTION
Page 65 and 66:
BRIGHTNESS & CONTRAST VARIATION Eig
Page 67 and 68:
• Shadow protection level: can be
Page 69 and 70:
DIGITAL ICE, ROC, AND GEM CORRECTIO
Page 71 and 72:
DIGITAL ROC The Digital ROC (Recons
Page 73 and 74:
6 Adjust or move the Digital-GEM sa
Page 75 and 76:
USING JOB FILES The Standard Scan U
Page 77 and 78:
INPUTTING SCAN SETTINGS MANUALLY In
Page 79 and 80:
EXAMPLE: SETTING OUTPUT BY PRINT SI
Page 81 and 82:
9. MAKING THE FINAL SCAN WHEN USING
Page 83 and 84:
CUSTOM WIZARD This function automat
Page 85 and 86:
2 QUITTING THE STANDARD SCAN UTILIT
Page 87 and 88:
WHEN USING THE IEEE 1394 CABLE WITH
Page 89 and 90:
OUTPUT COLOUR SPACE The choice of o
Page 91 and 92:
SCANNER NOTES Scanner colour profil
Page 93 and 94:
JOB FILE LIST • To save new Job f
Page 95 and 96:
TECHNICAL SPECIFICATIONS Scan type:
Page 97 and 98:
USER TECHNICAL SUPPORT Please conta
Page 99:
Input-resolution list box .........
show all

DiMAGE Scan Elite II Hardware OM - Konica Minolta Photo Imaging ...

Create successful ePaper yourself

Delete template?

Save as template?