CETAC M-7600 Mercury Analyzer Operator's Manual

More documents

Recommendations

Info

Operator’s Manual Chapter 6: Troubleshooting the Mercury Analyzer IPSetup a product of Netburner, Inc. IPSetup.exe is installed in the following folder: C:\Program Files\QuickTrace\IPSetup On the right hand side of the window will be a list of all Netburner-based devices (like the M-7600) that the program could find on the network. If you select one such device, its current IP configuration will appear on the left hand side of the window. These settings can be changed, and the changes applied simply by clicking on the “Set ” button in the middle. (The gateway and DNS settings are not necessary if the M-7600 is connected directly to the PC, and can be left at 0.0.0.0 or any other legal value.) After making a change this way, turn the M-7600 off, wait 15 seconds, then turn it back on. If no device is detected by the IPSetup tool then it is likely that either the device is not powered, or it is not connected to the network that the computer running IPSetup is connected to. It should be noted that IPSetup uses UDP, so if the M-7600 is not directly connected to the PC, a router or bridge could be blocking UDP broadcasts. Step 3: Check the Subnet Configuration Using the Define QuickTrace Hardware Tool Once we know the device is connected to the network, and powered on we have to make sure the device is on a logical subnet that our PC can communicate with. 1 To start CETAC's Define QuickTrace Hardware tool, click Start | All Programs | CETAC Technologies | QuickTrace | Define QuickTrace Hardware. If the instrument is seen and connected to, then subnet compatibility is assured. Skip to “Step 4: Check for an IP address conflict” on page 137. If the instrument is not detected, then we’ll have to look at the IP address of the device. 2 Open the Windows network connections dialog. For Windows 7, open the Windows Control Panel and select Network and Internet | Network and Sharing Center | View network status and tasks. Figure 6-2 Network and Internet Settings (Windows 7, View by Category). 134
CETAC QuickTrace M-7600 Mercury Analyzer Chapter 6: Troubleshooting the Mercury Analyzer For Windows XP, open the Windows Control Panel and select Network Connections. Note that the remainder of the instructions below assume Windows 7. 3 Click on the connection name (shown in blue). Figure 6-3 Network Connections in the Windows Control Panel. The network status will pop up. 4 Click Properties. Figure 6-4 Network Connection Properties Button. 135
Page 1 and 2:
CETAC M-7600 Mercury Analyzer Opera
Page 3 and 4:
Contents 1 Introduction ...........
Page 5 and 6:
M-7600 Mercury Analyzer Operator's
Page 7 and 8:
1 Introduction Overview The CETAC Q
Page 9 and 10:
CETAC QuickTrace M-7600 Mercury Ana
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
2 Preparing for Installation Instal
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
3 Installing the Analyzer Installat
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
4 Using the Analyzer Operation of t
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84: CETAC QuickTrace M-7600 Mercury Ana
Page 103 and 104: 5 Maintaining the Mercury Analyzer
Page 133: 6 Troubleshooting the Mercury Analy
Page 157 and 158: 8 Glossary A Amperes, electrical cu
Page 159 and 160: ng Nanogram (10 -9 gram), mass or w
Page 161 and 162: Index autosampler data cables, 44,
Page 164: Manual Part Number 480195 Rev 2 Pri
show all

CETAC M-7600 Mercury Analyzer Operator's Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?