CETAC M-7600 Mercury Analyzer Operator's Manual

More documents

Recommendations

Info

Operator’s Manual Chapter 7: Safety and Regulatory Information Electrical Characteristics Power requirements M-7600 Mercury Analyzer Input: AC Voltage, Frequency, and Current 100-240 V ~ 50-60 Hz 3 A Installation Category: CAT II (Line voltage in appliance and to wall outlet) AUX POWER Outputs: 24 V DC, max 3.33 A each connector, max 6 A total Table 7-2: Power Requirements Input and output connectors Connector AUX INPUT Description and characteristics Trigger signal input, reserved for future use. Connect only as instructed by CETAC Technologies. (Max 28V DC) ETHERNET Ethernet connection. (Max 5V) Table 7-3: Electrical Input and Output Connectors on the Analyzer 150
CETAC QuickTrace M-7600 Mercury Analyzer Chapter 7: Safety and Regulatory Information Safety Notices WARNING INJURY HAZARD If the equipment is used in a manner not specified by CETAC Technologies, the protection provided the equipment may be impaired. Repair or service that this not covered in this manual should only be performed by qualified personnel. Replacement Parts Except as otherwise noted, all replacement parts must be obtained from CETAC Technologies. Visit www.cetac.com for a current list of available spare parts. Chemical Hazards WARNING POISON HAZARD Do not prepare organomercurial concentrates unless you are qualified to do so. Improper handling can result in injury or death. The handling of organomercurial concentrates which may be used in the preparation of process standards presents a substantial (potentially lethal) safety hazard. Only an experienced, professionally trained organo-metallic chemist, knowledgeable and skilled specifically in the safe handling of organomercurials (using approved apparatus and approved protection measures in an approved facility) should attempt to prepare diluted organomercurial process standards from concentrates. CETAC Technologies assumes no liability for the handling of organomercurial concentrates or the preparation, handling, or use of diluted organomercurial process standards. Instead, CETAC Technologies recommends use of appropriate standard reference materials to validate sample preparation (dissolution/digestion) and use of inorganic mercury standards for instrument calibration. Power Cord Set Requirements The power cord set supplied with your instrument meets the requirements of the country where you purchased the instrument. If you use the instrument in another country, you must use a power cord set that meets the requirements of that country. Power Cord Safety Maintenance The operator should check the power/signal supply cord condition. The equipment should not be operated if the mains inlet is cracked or broken. Any obvious damage to the case (from a drop or fall) should be checked by service personnel for loose or damaged parts. See individual parts lists for approved replacement parts 151
Page 1 and 2:
CETAC M-7600 Mercury Analyzer Opera
Page 3 and 4:
Contents 1 Introduction ...........
Page 5 and 6:
M-7600 Mercury Analyzer Operator's
Page 7 and 8:
1 Introduction Overview The CETAC Q
Page 9 and 10:
CETAC QuickTrace M-7600 Mercury Ana
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
2 Preparing for Installation Instal
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
3 Installing the Analyzer Installat
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
4 Using the Analyzer Operation of t
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
Page 97 and 98:
Page 99 and 100: CETAC QuickTrace M-7600 Mercury Ana
Page 103 and 104: 5 Maintaining the Mercury Analyzer
Page 133 and 134: 6 Troubleshooting the Mercury Analy
Page 149: CETAC QuickTrace M-7600 Mercury Ana
Page 157 and 158: 8 Glossary A Amperes, electrical cu
Page 159 and 160: ng Nanogram (10 -9 gram), mass or w
Page 161 and 162: Index autosampler data cables, 44,
Page 164: Manual Part Number 480195 Rev 2 Pri
show all

CETAC M-7600 Mercury Analyzer Operator's Manual

Create successful ePaper yourself

Delete template?

Save as template?