CETAC M-7600 Mercury Analyzer Operator's Manual

More documents

Recommendations

Info

Operator’s Manual Chapter 3: Installing the Analyzer NOTE In most cases, CETAC will pre-configure the network cards for your laboratory. If you were not able to supply the necessary network information to CETAC, or if you will be supplying your own PC, then you will need to set up the network cards yourself as described in this document. Refer to the M-7600 Mercury Analyzer PC Setup Guide and the QuickTrace Software Manual for instructions on how to configure the network settings on the PC and on the M-7600. To Power On the System for the First Time (PC Configured by CETAC) CAUTION When you turn off the QuickTrace M-7600, wait at least 15 seconds before turning it back on. Rapidly cycling power can cause the optical monitoring feedback system electronics to temporarily malfunction, potentially resulting in an optical performance error. 1 Power on the PC, QuickTrace M-7600 mercury analyzer, and the autosampler. 2 Check to ensure that the communication cables are properly connected. 3 Start the QuickTrace software. 4 When the software is initializing, it will test the connections to the QuickTrace M-7600 mercury analyzer and the autosampler. The QuickTrace M-7600 software runs a test routine at startup to test the various interfaces throughout the system. The software will give a report on the status of the interface if there is a failure. To Power On the System for the First Time (Customer- Supplied PC) If you are supplying your own PC, you will need to set up drivers to communicate with the M-7600 and the autosampler. CAUTION When you turn off the QuickTrace M-7600, wait at least 15 seconds before turning it back on. Rapidly cycling power can cause the optical monitoring feedback system electronics to temporarily malfunction, potentially resulting in an optical performance error. 1 Power on the PC, QuickTrace M-7600 mercury analyzer, and the autosampler. 2 Check to ensure that the communication cables are properly connected. 3 Run the USB device driver installation program. Navigate to C:\Program Files\QuickTrace\USB Drivers then double-click CDM2.02.04. 64
CETAC QuickTrace M-7600 Mercury Analyzer Chapter 3: Installing the Analyzer 4 Select All Programs | CETAC QuickTrace | Specify Installed Hardware. Figure 3-64 Starting the Specify Installed Hardware Program. 5 Select the M-7600 analyzer. Figure 3-65 Selecting the Analyzer. Once the M-7600 is chosen the software will search the network for analyzers. 65
Page 1 and 2:
CETAC M-7600 Mercury Analyzer Opera
Page 3 and 4:
Contents 1 Introduction ...........
Page 5 and 6:
M-7600 Mercury Analyzer Operator's
Page 7 and 8:
1 Introduction Overview The CETAC Q
Page 9 and 10:
CETAC QuickTrace M-7600 Mercury Ana
Page 11 and 12:
Page 13 and 14: CETAC QuickTrace M-7600 Mercury Ana
Page 17 and 18: 2 Preparing for Installation Instal
Page 25 and 26: 3 Installing the Analyzer Installat
Page 63: CETAC QuickTrace M-7600 Mercury Ana
Page 75 and 76: 4 Using the Analyzer Operation of t
Page 103 and 104: 5 Maintaining the Mercury Analyzer
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
6 Troubleshooting the Mercury Analy
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
Page 155 and 156:
Page 157 and 158:
8 Glossary A Amperes, electrical cu
Page 159 and 160:
ng Nanogram (10 -9 gram), mass or w
Page 161 and 162:
Index autosampler data cables, 44,
Page 164:
Manual Part Number 480195 Rev 2 Pri
show all

CETAC M-7600 Mercury Analyzer Operator's Manual

Create successful ePaper yourself

Delete template?

Save as template?